The coefficients of friction between the block and the incline are Us 0.35 and μ = 0.25. Determine whether the block is in equilibrium, and find the magnitude and direction of the friction force when 0 = 25° and P = 750 N. 1.2 KN P

Q: A table top was measured with the following dimensions- Length: 215.1cm +/- 0.05cm, Width: 91.2cm…

A: To find the volume and uncertainty σV of the table-top.

Q: Enhanced EOC: Exercise 3.7 The coordinates of a bird flying in the xy plane are given by z(t) = at…

A: A) Determine the x-component of the velocity. Determine the y-component of the velocity.

Q: What is the z-component of the net force on the airplane? Express your answer in terms of the given…

A:

Q: can i get a picture solution, because the above is really hard to understand

A: Given, Total energy is twice the rest energy.

Q: If the interaction between the two electrons in a helium atom can be approximated as e? -(2a)*8(ñ –…

A: Using zeroth order approximation ψ is obtained by neglecting electron-electron repulsion. The…

Q: 6. (a) A lμC charge is at the center of the square shown below. How much external work is needed to…

A: ghkkjbjvh

Q: prove that [L2,Lz]=0

A: L^2 is an operator that represents the square of angular momentumIt is equivalent toL^2 = L^x2 +…

Q: d) If [F,G] = 0=[F*,G™] = 0, where m,n integers > 0 e) If [F,H] = 0 & [G,H] = 0= [F G,H] = 0

A: we can use the properties of commutator brackets.

Q: S₁√ B. ds =

A:

Q: How does the middle equation equate to the RHS

A: Step 1:  Proving Fμυ​=gμα​gυβ​Fαβ STEP 2:  PROOVING gμα​gυβ​Fαβ=(gFgT)μυ​  STEP 3: PROOVING…

Q: How do you get from J/V^2 to mF?

A: Given: C=2EV2         To know, unit conversion

Q: Would you mind solving this on paper, for it  too is hard to understand in this format?

A:

Q: (b) What is the resistance (in Q) of a 4.50 × 102 Q, a 1.90 kN, and 5.00 kM resistor connected in…

A:

Q: ice water metal isolation A metal block with mass mm initially has a temperature Tm,0 (with Tm,0 >…

A: Given data:Mass of the metal block: Mass of water: Mass of ice: Initial temperature of the metal…

Q: L*Yem (0,6) = NYem+1 (0,6), where N is a number, (a) show that |Nf = (L*Ycm, L*Yam). (b) and hence…

A:

Q: Two forces, F₁ and F2, act at a point, as shown in (Figure 1). F₁ has a magnitude of 9.00 N and is…

A: Given:-  The magnitude of the vector  Force F1 and F2 as  F→1= 9 N F→2=6.20 N  The angle is α= 61.0°…

Q: Which is NOTa small angle approximation?

A:

Q: The heat engine shown in the figure uses 1.9 mol of a monatomic gas as the working substance. Part E…

A:

Q: Prove that dx (csc x): = -csc x cot x.

A:

Q: How do I put the equation delta y=viy(delta t) + 1/2ay(delta t)2 in terms of delta t? In other…

A: The given equation is: ∆y=viy∆t+12ay∆t2…

Q: For example, for the equation = TV, if G = y and V = x, what represents m? If we solve for G, then G…

A:

Q: Cartesian to Cylindrical Coordinates.

A:

Q: ote as w

A: Given data: The initial angular velocity and angular velocity can be given as ωi=138 rad/s &…

Q: uld you possible write out the  step 2 part? It looks really confus

A: Solution: According to mass law, the transmission loss and incidence frequency is related by the…

Q: Use a scientific calculator to calculate Delta L_fS for D1 = 20 meters and D2 = 40 meters.

A: Delta is used to represent a change in the value of a variable. Here variable is the length. Initial…

Q: I'm having some issues understanding my physics homework. It doesnt look like what we were doing in…

A: (a)(i) Point P, where the speed is maximum is located at the lowest point on the roller coaster. At…

Q: In an insulated vessel, 248 g of ice at 0°C is added to 635 g of water at 19.0°C. (Assume the latent…

A: Solution:-Given thatmass of ice=248 g=0.248 kginitial temperature of ice=0°Cmass of water=635g=0.635…

Rotational Equilibrium And Rotational Dynamics

In physics, the state of balance between the forces and the dynamics of motion is called the equilibrium state. The balance between various forces acting on a system in a rotational motion is called rotational equilibrium or rotational dynamics. 

Equilibrium of Forces

The tension created on one body during push or pull is known as force.