The coefficient of kinetic friction between the 30-mm- diameter pin and the pulley is 0.25. Calculate the tension T required to (a) raise the load and (b) to lower the load at a constant speed. Neglect the mass of the pulley. To 30 500 kg 27

The coefficient of kinetic friction between the 30-mm- diameter pin and the pulley is 0.25. Calculate the tension T required to (a) raise the load and (b) to lower the load at a constant speed. Neglect the mass of the pulley. To 30 500 kg 27

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A block with a mass of 100 kg (left-block) is connected to another block of mass M (right-block) by a cable that passes over a fixed drum as shown below. The coefficient of static friction between the left-block and the floor is 0.45, between the right-block and floor is 0.4, and between the cable and the fixed drum is 0.25. Ignore tipping (overturning). Determine the minimum mass of the left-block for which motion does not occur.
The coefficient of friction between the inner pulley and the belt is 1/π. Find the maximum value of W that can be supported without rotating the compound pulley P or slipping the belt on the compound pulley P. Pulley B is frictionless. A 200 lb A W
A screw of the type indicated below is used to apply a force to the wedge, which then moves the 500-kg block. If the coefficient of static friction between all contacting surfaces is 0.2, what is the minimum torque T that must be applied to the screw? Neglect the weight of the wedge.
The weight of the two boxes as shown in Figure are W1 = 500 N and W2 = 100 N. The coefficient of static friction, us and kinetic friction uk between box W1 and the inclined surface are 0.12 and 0.10 respectively (a) Determine the minimum tension force which the worker must exert on the rope to prevent the boxes from sliding (b) What range of tension force should be exerted on the rope so that the boxes remain stationary? 30
A 25-kg ladder, 4m long rests on a rough floor and against a vertical wall. The ladder makes an angle of 35o with the horizontal as shown. It starts to slip when a man weighing 75 kg has climbed halfway up. If coefficient of friction at the wall is 0.2, determine the coefficient of friction at the floor.
None
In the figure shown the blocks weighs 400 N each. It is held in the positionby a belt that passes over a fixed wheel , the belt being subjected to a horizontal force P at its end. The coefficient of friction between blocks and the inclined plane is 0.20 and 0.25 between the belt and the wheel. Calculate the ff:a. Magnitude of P in N when the block is at impending motion up the plane.b. Tension in the belt near the block in newtons.c. Contact angle between the wheels and the blocks.
Calculate the horizontal force Pon the light 11° wedge necessary to initiate movement of the 36-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.40. Also determine the friction force Fg at point B. (Caution: Check carefully your assumption of where slipping occurs.) 36 kg A B P > 119 Answers: P = 108 N FB = i 27.1 N
High-strength bolts are used in the construction of many steel structures. For a 1-in.- nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded. You must show a free body diagram of your block and incline analysis of the bolt and nut, and clearly indicate your force triangle, if any.
A box of mass m is resting in the flat bed of a truck which is stopped at a red light on a road which slopes upward at an angle qabove the horizontal. The coefficients of friction between the box and the truck bed are given by μs and μk.The light turns green and the truck begins to accelerate.Write all answers in terms of variables given in the problem and any appropriate constants. 1)Find the work done by friction as the box slides to the back of the truck in terms of m, L, μk, q, and any appropriate constants.
A steel ramp is used by a worker in a factory to move a cardboard box. The box weighs 40 lb with a center of gravity at point G, the force applied by the worker is parallel to the ramp and the coefficient of friction between the box and ramp is μs = μk = 0.3. Determine the value of the normal force N. Determine the force the worker must apply to slide the box up the ramp. Determine the friction force F acting between the ramp and the box if the worker slid the box up the ramp. Determine the force the worker must apply to slide the box down the ramp. Determine the friction force F acting between the ramp and the box if the worker slid the box up the ramp.
A wooden block of mass 40 kg resting on an inclined plane is pulled upward by a force parallel to the plane. The plane is inclined at 13° with the horizontal. Coefficient of friction between the plane and the block is 0.16. Determine the force required to start the motion of the block on the plane.