I ReviewThe circular cam rotates about the fixed point O with aconstant angular velocity w. (Figure 1)Part ADetermine the velocity v of the follower rod AB as a function of 0.FigureExpress your answer in terms of the variables 0, d, R, r, and w. Include arguments of thetrigonometric functions in parentheses.1 of 1View Available Hint(s)vec?KΣΩv =That's not quite right. Please check your formatting and try again.圓

Answered: Image /qna-images/answer/509c695c-17bc-47a6-9cb4-3e9ca278d247.jpg

Answered: The circular cam rotates about the…

The circular cam rotates about the fixed point O with a constant angular velocity w. (Figure 1) Part A Determine the velocity v of the follower rod AB as a function of 0.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im F P S a M Im R IU - a' W 0.8m 3m A. Calculate the cable RQ force's magnitude (in kN), FRQ. B. Determine the support reactions at Z (in kN). Zx = ?, left, or right? Zy = ?, down or up? 4 m C. Determine the internal moment (in kNm) at the midpoint of bar RUZ-section a-a', Ma-a'. Show your answer by drawing a corresponding FBD showing Maa", other unknown or known external and internal forces.
5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N
Two solid steel shafts (G= 77 GPa) are connected by the gears shown. The support D is fixed, and the bearings allow free rotation of the shaft. The radius of gear B is ³ = 20 mm, and the radius of gear C is rc = 60 mm, If T₁ = 75 Nm, 1. Draw the torque distribution along shaft DE. 2. Calculate the angle through which end A rotates E rc = 60 mm 20 mm 500 mm 24 mm 400 mm
A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS B.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND BY PARTS ITEM 1.0 25 kN/m A D В C- -3 m-- --10 m- -4 m-| EI = constant E = 200 GPa I = 500(106) mm4
Question 45 of 46 A prybar is used to remove a nail as shown. Determine the moment of the 265-N force about the point O of contact between the prybar and the small support block. The moment is positive if counterclockwise, negative if clockwise. 265 N 18 355 mm 59 0-T 32 mm Answer: Mo = N-m
find the time period and natural figure of the system Sholon in the Cross-section of the beam is 30mm X 60mm E=200GPa A 2m 3m {60 N/mm m frequency ] =20kg below the Also find the mass given an initial displacemen at &t=25 and also find the maximum displacement.
In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A torque of TC = 440 N-m is removed from the shaft at gear C, and the remaining torque is removed at gear D. Segments (1) and (2) are solid 38-mm-diameter steel (G = 80 GPa) shafts, and the bearings shown allow free rotation of the shaft. Assume DA = 110 mm, DB = 370 mm, L1 = 1.7 m, and L2 = 1.1 m. Calculate the rotation angle of gear D relative to gear B.
A half section of pipe rests on a frictionless horizontal surface as shown. If the half section of pipe has a mass of 21 kg and a diameter of 300 mm, determine the bending moment at point Jwhen e = 90°. В A C The bending moment is N-m in the (Click to select)
900 N 4.00m A 800 N/m B 600 N 1.80 m 1.20 m Use a ruler to prepare the required FBDs to determine the magnitude (no sign required) of the horizontal force at pin B. Bx. A. B. and C are smoothless pins
PLATE # 3 CALCULATE Oo AND Yo OF THE BEAM LOADED AS SHOWN USING CONJU GATE BEAM METHOD 5KN/m 20KN 30 KN M 2m 2m 2m 2m Im 21 E CONSTANT
SOLVE THE FOLLOWING DIFFERENTIAL EOUATIONS.
The 80 mm diameter shaft is made of 6061-T6 Aluminum having an allowable shear stress of τallow = 60 MPa. Find the maximum allowable torque T. Also, find the corresponding angle of twist of disk A relative to disk C.