Not fully understanding Question #1The circuit shown in Figure #1 is analysed using superposition. Theindependent currents of sources "A" ånd "B" were found to be 5A and 3Arespectively.Determine the current throuh cach resistora.b.Hence, dateulate the total power dissipated in the circuit.Validate the power calculated in “b" by determining the powersupplied OR absorbed by each power sourceС.10 2"B"48Ω1562"A"Figure #1

Answered: Image /qna-images/answer/8705d2b3-d72a-4517-812f-877f9d0300a4.jpg

The circuit shown in Figure #1 is analysed using superposition. The independent currents of sources "A ånd “B" were found to be 5A and 3A respectively. Determine the current throh cach resistor a. b. Hence, dateulate the total power dissipated in the circuit.

The circuit shown in Figure #1 is analysed using superposition. The independent currents of sources "A ånd “B" were found to be 5A and 3A respectively. Determine the current throh cach resistor a. b. Hence, dateulate the total power dissipated in the circuit.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 1RQ: 1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive...

See similar textbooks

Similar questions

dhe circuit shown in figure (1), use the method of source transformation to calculate the following: a. The current iz and the voltage v, b. The power dissipated in each source c. The power dissipation in all resistors 2. 3. 9 A Figure (1) 2/4
a. In the circuit shown in Figure below, what is the current i in amperes? Round-off answer to 2 decimal places and enter answer w/o units. b. In the circuit shown in Figure below, what is the current i3 in amperes? Round-off answer to 2 decimal places and enter answer w/o units. c. In the circuit shown in Figure below, what is the voltage V0 volts? Round-off answer to 2 decimal places and enter answer w/o units.
Arrange a simple three-phase system and measure the power consumed by the load. You may use wattmeter or any other digital meter, while measuring three-phase power. The connection diagram is shown in Figure 3. Your report should show details of the three-phase load and connection diagram relating to the power you have measured. This work should be evidenced by photograph in the report.
When you are solving for circuit problems from the data obtained from experiments, what is the significance if you got a negative sign from a calculation? a. No significance B. It means you did something wrong on your calculation. C. Real resulting current or voltage is in the opposite direction to one assumed. D. You probably used smaller scaling factor. Explain ty.
Hi, I need a correct answer for this assignment question Thanks
A heater has 3 equal induction-free elements, each with a resistance of 10 ohms. The elements is delta connected and the oven is connected to a three-phase voltage of 230V / 50Hz a) How much power is developed in the oven in total? The elements is now star connected instead and the oven is connected to 400V three-phase voltage. b) How much power is being developed in the furnace now? c) How large will the power be if the elements in the star connection are connected to 230V three-phase voltage? d) How would you connect the elements if you want to use 230V single-phase voltage and want the same power as under question b)? e) How much current does the oven draw now? Comment on the result ..
2 b) A circuit takes a current of 3A at p.f of 0.6 lagging when connected to a 115 v, 50 Hz supply. Another circuit takes a current of 5 A at a p.f of 0.707 leading when connected to the same supply. If the two circuits are connected in series across a 230V, 50 HZ, Calculate- 1. The current 2. The power consumed 3. The p.f of the circuit
Question 2 This system below is a model of a custom electric heating system: R₁ 120 V Lw www R3 R4 R₂ Bu 1. Determine the voltage across each resistor (heating element). bus R₁ = 60 R₂ = 40 R3 = 100 R4 = 120 M 0221
For the circuit shown in Figure, find the following: a. The magnitude of current in the circuit, I. b. The total power delivered by the voltage source, P,. c. The value of the unknown resistance, R./ d. The power dissipated by each resistor. 1 ka 4 ko E- 90 V RT- 12 ka 3 ka
0 At which places the dresel power stations are finding fevort Why? g) How do voids in the insulation cause breakdlown ofthe.cable? h) What is the function of cendenser in steath powerplant?
use these two images to answer all these questions: What are the differences between ac and dc meters? Can you compare the value of the current in the load resistance for the same value of voltage with ac and dc supply? What is the function of the autotransformer in this circuit? Can you use an autotransformer to obtain variable output voltage from a fixed dc supply? What will happen if dc meters are used instead of ac meters in this circuit? What the difference between resistance and impedance is when referred to dc and ac measurements?
Please show your detailed solution Number 41 What is the “wattage” rating of a lamp whose hot resistance is 150 W when connected to a 117-V 25-Hz source? A. 64.53 W C. 129.06W B. 91.26 W D. 912.6 W