The circuit shown below was used as a current source in a LED lighting application, and voltage quantities given below were measured for this circuit. Calculate the collector current, Ic ? Ien dınlntma aulama -nhidaki gerilım .ilmüstür .....ini anlavinız l-? Measurements: VRc = 1 V, VRb = 0.80 V, VBE = 0.65 V, VCE = 7.95 V, V2= 3.47 V Re VReS 100 V1 12 Rb B Q1 10k 2N3904 Re 100 O a. 5.00 mA O b. 10.00 mA O c. 2.50 mA O d. 2.00 mA O e. 3,33 mA

The circuit shown below was used as a current source in a LED lighting application, and voltage quantities given below were measured for this circuit. Calculate the collector current, Ic ? Ien dınlntma aulama -nhidaki gerilım .ilmüstür .....ini anlavinız l-? Measurements: VRc = 1 V, VRb = 0.80 V, VBE = 0.65 V, VCE = 7.95 V, V2= 3.47 V Re VReS 100 V1 12 Rb B Q1 10k 2N3904 Re 100 O a. 5.00 mA O b. 10.00 mA O c. 2.50 mA O d. 2.00 mA O e. 3,33 mA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

True or False answer all with brief explain
1. Given:VS1: -1 voltsVS2: 24 voltsB=beta: 150RE: 330 ohmsRC: 750 ohmsVC: ? volts
Diagram showing zero basing in field effect transistors as applied in electronics
a1.Using a dc and ac voltmeter to measure the output signal from a filter cicruit, we obtain readings of 25 v dc and 1.5 V rms.Calculate the ripple of the filter output voltage. a2. 2 a dc voltage provides 60v when the output is unloaded.When connected to a load, the output drops TO 56 V. calculate the value of voltage regulation.
UTM system. (a) Describe their different function and operation in the DC supply system. UTM (b) Can zener replace the function of the regular diode in the application described in a DC power supply A UTM in question 3(a)? Justify your answer. TM UTM UTM 2.UTM UTM UTM 5 UTM UTM UTM & UTM & UTM UTM &UTM UTM TM UTM & UTM UTM
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
a) Draw the energy band diagram of a MOSFET transistor, when -5 volts are applied to the drain contact. b) Explain what will happen to the Fermi level at the source contact and the drain contact in the following scenarios (Use an appropriate energy diagram to illustrate your answer): A positive voltage is applied to the drain contact. A positive voltage is applied to the source contact. c) Explain why current flow in a MOSFET transistor. Use a diagram to illustrate your answer.
2 V 1ΚΩ VOUT Find the following: a. Vout b. Small signal model of the diode under these conditions (Do NOT consider capacitance across the diode junction and the resistance of the semiconductor material outside the diode junction) c. Approx. peak-to-peak value of the AC component of Vout if a 1 mV RMS sinusoidal signal is added to the 2 V DC source. Given that: reverse saturation current is 1.5 x 10-14 A, ideality factor is 1.1, and the circuit is operating at 27°C.
Design a 15 V Zener regulator for the following conditions: 1) The load current IL ranges from 200 mA to 300 mA.2) The source voltage ranges from 21 V to 25 V. Based on your design results,a) Draw the Zener regulator circuit.b) Calculate the power ratings for both Zener diode and resistor Ri
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. The input voltage, Vi, varies from 30 in Table B.1, select one zener diode that is suitable for the above circuit operation. Show relevant calculation to justify your selection. UTM OV to 50 V. Based on the parameters given UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM UTM V, SUTM & UTM TM 2.5 k2 UTM UTM UTM Table B.1 Zener Diode Vz (V) UTM &UTM & UTM PDMAX (W) ZA UTM UTM ZB 0.5 5 ZC 1 15 ZD 0.5 15 JUTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 UTM UTM20 & UTM & UTM & UTM UTM UTM TM UTM TTM UTM
Instructions Calculate the DC voltages and currents in the circuit. Find for the current emitter, collector current and collector voltage. +12v 5kN 5kN Voz Vor Q2 Q1 Viz VE 2.7kN
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. UTM Show relevant calculation to justify your selection. The input voltage, Vi, varies from 30 V to 50 V. Based on the parameters given in Table B.1, select one zener diode that is suitable for the above circuit operation. 5 UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM 3 UTM TM Vi 2.5 ko 5 UTM 5 UTM VL UTM UTM UTM UTM UTM Pigure B 3 Table B.1 Vz (V) UTM UTM 3 UTM PDMAX (W) Zener Diode ZA UTM & UTM ZB 0.5 5 1 15 ZD 0.5 15 UTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 5 UTM UTM 20 5 UTM & UTM & UTM