The cable will break when the maximum tension reaches Tmax = 12 kN. Determine the uniform distributed load w required to develop this maximum tension

Q: The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel…

A: Consider the following free body diagram:

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

A:

Q: Two cables are tied together at C and are loaded as shown. Knowing that P = 328 N and R = 495 N,…

A:

Q: Suppose the pulley is removed. Resolve for the tension in the cable. 6000N is the wrong answer

A:

Q: . In a PSC, the tensioning system may be classified into:

A: This question is related to Pre Stressed Concrete from RCC design.

Q: The Pratt roof trusses are uniformly spaced every 3.60 m. The deck, roofing material, and the…

A: Average weight(dead load)Wind loadSpacing of truss, To find: The concentrated loads on the joints…

Q: A 600 N B 400 N C E D 150 mm 100 mm-150 mm- 80 mm 100 mm

A: Beam ABCD supported by cables BE and CF

Q: Question 3: calculate the forces in all the members of Cable R = Last two digit of Roll No. S 2.74 m…

A:

Q: esign a purlin section for the following data: -paullng of roof trusses c/c Dead load of roofing…

A:

Q: Determine the minimum downward force to keep the block from slipping. The block weighs W kN. The…

A:

Q: I. Method of Members 1. The portable table shown is to support a load P = 1.5 kN at a variable…

A: P (load) = 1.5KN L = 1.5m

Q: 34. In a PSC, the tensioning system may be classified into: А. О З В. О 2 С. О 5 D. O 4

A: Answer : option (B) 2 is correct.

Q: Problem 2. A simply supported truss loaded as shown. Required: (1) Reaction @ supports A & C; (2)…

A: Here we will use method of joints to calculate the force in each member,in which at every joint we…

Q: Cable ABCDE supports the loading shown. Determine the tension in member DE, the value of Yd and the…

A: Determine the tension in member DE, the value of Yd and the value of Yb

Q: Draw the force diagram of pipe ABCDE - Determine the magnitude of the concentrated force, F_cd,…

A: Given:Required:Force diagramMagnitude of concentrated force FCDTension forces in terms of TUnit…

Q: A 500 Ib/ft uniform load w is applied to 6 ft rigid horizontal bar CA, pin supported at Cin single…

A:

Q: Bar ABC is supported by two cables and a inge. Compute the new temperature of alumi num cable if the…

A: Given, Ls = 0.9 m  La = 1.2m Es = 200 x 109 N/m2 Ea = 70 x 109 N/m2

Q: im Determine the deflection in each point of (A,B,C and D) for the steel system shown in Figure (2)…

A:

Q: The 8-ft bar is supported by a ball and socket support at A, the cable BD, and a roller support at…

A:

Q: If the aluminum cable is removed and no lon ger supporting Bar ABC. A concentrated loa d is then…

A: Answer  Let us first draw the free body diagram and calculate the shear force at B. Let us…

Q: Q2. Determine the tension developed in each cable for equilibrium of the P crate. L112 L1 L2 L3 L4…

A:

Q: Answer in hand written ty beed asap

A: 1. Maximum Ordinate of Influence Line for Member AB: The maximum point on the influence line for…

Q: gage cold-formed steel channel used as pur uss 4m apart. Sag rods are placed at midspar acting on…

A:

Q: 8-21 The offset link has a width of w = 200 mm and a thick- ness of 40 mm. If the allowable normal…

A: Step 1: formula of Stress(Oallow)Oallow = P/Area , Area = width(thickness) Step 2: solve now for…

Q: The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes…

A: Given:Required:Force diagramMagnitude of concentrated force FCDTension forces in terms of TNote: As…

Q: E 4 m 1 m 50 kN/m 6 m A B 16 m - 8 m

A:

Q: QIA rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and…

A:

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: 4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c)…

A: Away from the joint  (+ve) = tensile  Towards the joint (-ve) = compression

Q: PROBLEM 2 Determine the reactions at the supports at A, B and D. Assume that A is roller and B is a…

A: A frame is hinged at B and the roller is supported at A, with loading as shown. To determine the…

Q: A 30° 2 m 2 m C 2 m

A:

Q: a= 21 Deg b= 56 Deg c= 123 Deg d= 68 Deg e= 50 Deg F= 488 lb a B F 1- Determine the tension…

A:

Q: A vent structure of mass 233 kg is suspended from an l-beam as shown below. 6w E C 3w 4w D G. А y 2w…

A: Mass of structure = 233 kg

Q: Uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel…

A:

Q: A 300 mm M 30 mm 30 mm B. 150 mm 150 mm a) Determine the bending stress developed at point A. b)…

A:

Q: N 2. Determine the tension in the cables by the method of your choice. 14 A 60° 45° W = 12.5 KN www…

A:

Q: Determine the maximum weight W that can be supported as shown. Cable FG has a maximum strength of…

A:

Q: The floor system used in a school classroom consists of a 189-mm. reinforced stone concrete slab and…

A: Step 1

Q: Determine the maximum compressive force at member HL due to an 8kN point load.

A: Answer Let us first draw the ILD for member HL Pass a section through member HL as shown below…

Q: A boom hinged at the base of a vertical mast is used to lift a 2000 lb load. Find the tension in the…

A: An arrangement of boom is given in the question and it has been asked to determine reaction R at the…