The cable supports three 1779-N loads as shown. If the maximum allowable tension in the cableis 4003 N, find the smallest possible sag hc at C.Figure P6.84- 3.66Dimensionsin meter1779 N1779 Nאותלו

The FBD of the cable is shown below: Maximum tension T = 4003 N

Answered: The cable supports three 1779-N loads…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8) A shaft of diameter (d = 5-mm) is to be puled through a (4.5)-cm-diameter glycerin-filled sleeve as shown in Figure. The glycerin to be used has a dynamic viscosity of 1.5 Pa.s, and the cable is pulled by 60-N tensile farce. If the cable is to be pulied at a velocity of 0.02 m/s and the velocity profile equation though glycerin is (u = 0.6y + 20y), what is the length of the sleeve that can be used to provide this velocity? Assume that the cable can be kept at the center of the sleeve. Seve Shaft
Given the Cable as shown below that weighs 100 N/m with the Cartesian Plane x - y. Determine the equation of the catenary curve (in the form y = f(x)) L- B A 8 m 4 m y X
FN=130
B8
Find sag Yc and determine the largest force, F, that can be sustained by the cables if the maximum tension allowed is 720 N.At point C, what is the largest mass, M, that can be sustained by the cables if the maximum tension is 720 N.What is the tension in cable CD in Newtons (N)?What is the value of sag Yc in meters (m)?
Situation 6: Z-axis Three tension cables as shown on the figure are acting on a vertical post to remain its position at E. If the tension in cable AC is 4 N, determine the tension developed in the other cable so that the resultant at A X-axis y-axis will be vertical. sourcowa eHeocom 1 m m 4 m D
I need datiled solution with clear calculations
7.) (2 Points) Neglecting friction and the radius of the pulley. Determine the following: a.) the tension in cable ADB b.) the reaction at C. 150 mm A В 120 N 200 mm 80 mm 80 mm
For the system below, determine the time required for the B load to reach speed of 10 m/s if the cable in A is pulled by an engine with constant acceleration of 3m/s². Consider that at first the whole system was at rest.
Dr. Ammar T. Al-Sayegh Problem: 10 Name: Determine the angles Nand A made between the axes OA of the flag pole and AB and AC, respectively, of each cable. Page 8 6 m 1.5 m Z ID: 2m 4 m FB = 55 N 4 m 6 ENG202-Statics Fc = 40 N 3 m

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The cable supports three 1779-N loads as shown. If the maximum allowable tension in the cable is 4003 N, find the smallest possible sag hc at C. Figure P6.84 -24--24- - 3.6 - 3.66 Dimensions in meter 1779 N אטתו 1779 N