The c-clamp shown here has a solid, 2-cm- 10 cm diameter, circular cross-section. When it is adjusted so that F = 380 N, what is the maximum stress in plane A-A? A- a. 74.39 MPa b. 49.59 MPa c. 47.17 MPa d. 59.51 MPa

Q: T? D5 dx b) If we assume that the Darcy-Weisbach equation can be used for the head loss, how vill…

A: ∫x=0x=LdPdx=∫D1D232ρQ2π2D5dDdxP1-P2ρgL=32Q2π2D5gD2-D1LP1-P2ρg=32Q2π2D5gD2-D1   →Pressure gradient

Q: Please give me solution

A:

Q: Points B, D, and C lie on the x-y plane and vertical force F is on the z-axis. If force F subjected…

A: Given: The coordinates of different points are : O= (0,0,0)A=(0,0,-4)B= (3,3,0)C = (2,4.5,0)D =…

Q: 1. A body falling freely under the action of gravity passes two points 10 m apart, vertically in 0.2…

A: Given:-BC=10mt=0.2 secTo find :-AB

Q: Q.4/ Determine the magnitude of distributed force 5 KN/m and its location on the beam as shown. *…

A: Given that, AB is a beam having UDL of 5kN/m for span of 6 m from A

Q: Question 2)) In this figure .A 50mm diameter agitator propeller shaft of is utilized to drive a…

A: Given data: The diameter of the shaft is d = 50 mm. The compressive load on the shaft is P = 125…

Q: 8-7. The 100-lb cylinder rests between the two inclined planes. When P = 15 lb, the cylinder is on…

A: Given, Weight of the cylinder= 100 lb P=15  lb

Q: - As illustrated in the diagram, a cantilever beam supports a uniform distributed load of 60 kN/m.…

A:

Q: Consider the beam's cross-sectional area shown in ( Eigure 1). Suppose that a=4 in., b= 10 in., and…

A:

Q: .A car and its load weighs 40 kN and the center of gravity is 600 mm from the ground and midway…

A: GIVEN:W=40KNdistance between the rear wheel and front wheel =3m

Q: A current of 10.7 A is maintained in a single circular loop having a circumference of 80 cm. An…

A: Given Data Current, I=10.7 A Magnetic Field, B=2.0T Angle, θ=20° Circumference, C=80cm…

Q: The plate shown welghs 806 N and is supported in a horizontal position by two hinges and a cable…

A: Given data w=806N To find tension in the cable TCD

Q: Gasoline flows through a 1.6 inch diameter hose at an average velocity of 4 ft/s. What is the rate…

A: Given:Hose diameter, d=1.6 inch=1.612ftAverage velocity of gasoline through the hose, v=4 ft/sVolume…

Q: 200 kg mass rests on the beam. Post EF is 25 kg. Coefficient of static friction between the post and…

A: For simply supported beam AB: Hence, normal reactions at point "B" between post "BC" and beam AB…

Q: QUESTION line theory. , Calculate the collapse load (W collapse) for the slab shown, using the yield…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Determine the components of the moment (Mx, My, Mz) that the F force will create at the point C in…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Problem 2 Determine the total time t (in hrs.) required to fil the spherical tank with liquid whose…

A: Given:s=2.50m=400 Kg/mind=4 m

Q: 3. Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

A:

Q: The body and bucket of a skid steer loader has a weight of 2060 lb, and its center of gravity is…

A: The speed of the loader. Given: The weight of the body and bucket is P=2060 lb. The weight of each…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: boiling point

A: 446deg.c-answer

Q: Q2 The main factors that make a material more likely to undergo a ductile failure could be:

A: Ductile failure: Metals are commonly described as ductile or brittle. When they fail as a result of…

Q: 5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD =…

A:

Q: Which of the following stress strain curve shows an elastic behaviour to very high strain rate O a.…

A:

Q: Take the micro-body from the self-loading member, and bear the stress on it as shown in Figure a.…

A: For the given stress element,…

Q: For the 180° elbow and nozzle flow shown in the figure below, (a) determine the loss in available…

A:

Q: The steel bracket is used to connect the ends of two cables. 4 in. P P Part A If the applied force P…

A: The part of bracket which is 4 inches apart from the line of application of force P will experience…

Q: An axially loaded bar AB made of a homogeneous material with Young's modulus E shown below is held…

A: Given, Load = P Area AC = A1 Area CB = 1.5A1

Q: In a cruise controller the throttle of a car is controlled by a servomechanism with the aim of…

A:

Q: *12-48. The wooden beam is subjected to the load shown. Determine the equation of the elastic curve.…

A:

Q: Determine the total reaction at pin C if W-100N. Negligible weights of members and friction.

A:

Q: A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200…

A:

Q: Two (2) beams are subjected to different loading condition and position as shown. w1 w2 P x1 x2 x3 Ө…

A:

Q: Two airplanes are performing at an air show. Plane A travels along the path shown and, for the…

A: Given Data Acceleration of plane A is : aA=60 m/s2 Acceleration of plane B is : aB=250 km/hr=69.44…

Q: 1. For the following friction materials used for clutches, find the values of dry and wet friction…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.