The branching of a blood vessel is shown. Blood at pressure of 10 kPa gage flows in the main vessel at 0.004 m³/min. Estimate the blood pressure in branches 2 and 3, assuming that blood vessels behave as rigid tubes, that the flow is steady, frictionless, uniform, and that the vessel lies in the horizontal plane (i.e. you can neglect gravity). You can assume that for blood p = 1000 kg/m³, µ= 0.00282 Pa.s. Q3 Q2 = 0.0025 m³/min 60° 45° D2 = 0.75 cm D3 = 0.25 cm D, = 1 cm Q1 = 0.004 m³/Imin P, = 10 kPa gage

The branching of a blood vessel is shown. Blood at pressure of 10 kPa gage flows in the main vessel at 0.004 m³/min. Estimate the blood pressure in branches 2 and 3, assuming that blood vessels behave as rigid tubes, that the flow is steady, frictionless, uniform, and that the vessel lies in the horizontal plane (i.e. you can neglect gravity). You can assume that for blood p = 1000 kg/m³, µ= 0.00282 Pa.s. Q3 Q2 = 0.0025 m³/min 60° 45° D2 = 0.75 cm D3 = 0.25 cm D, = 1 cm Q1 = 0.004 m³/Imin P, = 10 kPa gage

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A capillary-tube laminar-flow element is needed to measure water flow of 0.01 in /min at 70 F. A…

Q: * In the spillway flow of Fig.(2),the flow is assumed uniform and hydro static at section 1 and 2.…

A: Given data: h1=5 mh2=0.7 m Need to determine the value of V1,V2 and force Fx per unit width of the…

Q: A cross section of a cylindrical draft tube proposed to be added to the exit of a reaction turbine…

A: Inlet cavitation mean cavitation is going to start so pressure at exit of the reaction turbine…

Q: : Neglecting the losses, calculate the required pump shaft horsepower. Figure (4)

Q: Water flows through a pipe, which is 30 mm in diameter and 55 m long, ab 2,75 m/s. Using Darcy's…

Q: Exercise 4.3 A pipe carrying 1800 /min of water increases suddenly from 10 cm to 15 cm diameter.…

Q: 5. A 50-m duct is 0.060-m in diameter (Figure 2). Calculate the flow rate (m³/sec). Pfluid=917 kg/m³…

Q: Water flows in a vertical channel. Use the given data to find the frictional pressure drop from the…

Q: Problem 3 ( Learning Outcome #13 Steady liquid jet with area A hits a stationary block and splits…

Q: Vortex shedding can be used to design a vortex flowmeter(Fig. 6.34). A blunt rod stretched across…

A: Given: The diameter of pipe, D = 5 cm = 0.05 m The sensor diameter, d = 8 mm = 0.008…

Q: l'aking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has…

A: Given:pipe diameter=100 mm or 0.1 mcontraction ratio=0.5No flow pressure head=P1ρg=3 m +10.3 m=13.3…

Q: Oil flows through a smooth pipe of diameter D-4 cm between points (1) and (2) that are 4 m apart at…

Q: = 1.006 m. Example 5.16. An open tank 10 m long and 2 m deep is filled with 1.5 m of oil of sp. gr.…

Q: Calculate the total head of a centrifugal pump and use the Darcy equation in computing the friction…

Q: The horizontal V fitting, steady, uniform flow at each section, incompressible, and neglect weight…

A: Let us find the velocities at 1 and 2 - Q=A1V1 =A2V20.4=π4201002V1=π481002V2V1=12.73ms, V2=79.577ms…

Q: Water flows steadily and smoothly along a horizontal pipe through a contraction and out into the…

Q: [With reference to the Bernoulli and Continuity equations, provide a theoretical analysis of how…

Q: The volume flow Q over a certain dam is a function of damwidth b , gravity g , and the upstream…

A: Given Data: Width of dam is b = 120 ft. The depth of water is H = 15 in. The flow rate is Q = 600…

Q: h 1 2 4.0 cm 1.0 mm 3

A: height of nozzle from top free surface of waterh=27cm=0.27mdiameter of nozzled=1mm=1×10-3m

Q: du Water flows past a flat plate that has a length L = 5 m and a width w = 2 m, as shown in Figure…

A: Given Data: Water flows past a flat plate Plate Length L=5 m Plate Width w=2 m shear stress at the…

Q: (Viscous flow) A viscous liquid (p = 0.015 lbs/ft², p = 1.74 slugs/ft³) flows through the annular…

A: The dynamic viscosity is The density is The inner radius is The outer radius is The pressure drop…

Q: Water flows downward in a pipe of 600 mm diameter at the rate of 2 m³/s. It then enters a conical…

Q: In the orifice and Jet flow experiment, the following data were collected. Water level =30 cm ,…

Q: A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm,…

Q: 25 mm Hg -> 0.09 m2 150 mm Water Problem 4.17 4.17. For a flowrate of 2 m'/s of air (y = 12.0 N/m')…

Q: Water with a density of 1 g/cm³ flows through a horizontal pipe. The pipe cross-section tapers from…

Q: A venturi meter has an inlet diameter of 65mm and a throat diameter of 26 mm. When measuring the…

A: The differential pressure head can be determined as,

Q: A vertical pipe of 40mm diameter carrying a flow of a Crude oil of u = 1.7 poise and relative…

Q: For H =3 m, calculate Qi and Q2. 3m KENTRANCE= 1.0 KENT = 1.0 Q1 Q2 Di- 20 cm Li=2m Dz= 50 cm t=002…

A: Given: To Find: Q1 and Q2 "Since you have asked multiple questions, we will solve the first…

Q: 1. Three reservoirs are connected by individual pipes to junction O as shown on the figure below.…

A: To find: The elevation of reservoir C and draw the final hydraulic gradient line. Given: The…

Q: liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a…

A: The objective of this question is to calculate the pressure gradient necessary to achieve a certain…

Q: 7.5. What is the smallest diameter of pipeline that may be used to carry 6.3 l/s (100 gpm) of jet…

Question

The branching of a blood vessel is shown. Blood at pressure of 10 kPa gage flows in the main vessel at
0.004 m3/min.
Estimate the blood pressure in branches 2 and 3, assuming that blood vessels behave as rigid tubes, that
the flow is steady, frictionless, uniform, and that the vessel lies in the horizontal plane (i.e. you can
neglect gravity). You can assume that for blood p= 1000 kg/m³, µ= 0.00282 Pa.s.
Q3
Q2 = 0.0025 m³/min
60°.
45°
D2 = 0.75 cm
D3 = 0.25 cm
D, = 1 cm
Q1 = 0.004 m/min
P, = 10 kPa gage

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.4 A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is Type your answer here.. SUBMIT
Q4.10) Figure 4.10 shows a flow-obstruction flowmeter with circular cross sections. The fluid is incompressible and has a constant density of p= 1250 kg/m3 when it goes through the flowmeter. The ratio of cross-sectional area A₁ to A2 is 3:1. The radius of Al is 0.04 m. The flow coefficient Kv is 0.95. The pressure difference is measured to be Ap = 300 Pa. A₁ Pi P2 Ap ↑42 A₂ P3=? I. Calculate the cross-sectional area of A1 and A2. II.Find the flow volume rate for the flowmeter. III. There is another pressure tap down-stream of the flowmeter; it is measuring p3, as shown in the diagram above. Arrange p1, p2 and p3 in increasing magnitude that is expected. (Note: there is no need to calculate the exact values of p1, p2 or p3, and their exact values are not needed to answer this question.) V. Briefly explain the answer in part (III). |
P.4.12 Oil of density 950 kg/m and viscosity 102 Ns/m² is to be pumped 10 km through a pipeline and the pressure drop must not exceed 2x10S N/m. What is the minimum diameter of pipe, which will be suitable, if a flowrate of 50 ton/h is to be maintained? Assume the pipe wall to be smooth. Use either a pipe friction chart or the Blasius equation f= 0.079/ Re4. Ans. d = 0.193 m D412
liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
plz solve it within 30-40 mins I'll give you multiple upvote
(a) Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system. (a) Area of the maximum sized pipe diameter (in m?) (b) Area of the minimum sized pipe diameter (in m2) (c) The minimum sized pipe diameter (in m) (d) The maximum sized pipe diameter (in m)
A) A 0.4 m diameter fan running at 970 rev min' is tested when the air temperature is 10 °C and the barometric pressure is 772 mm Hg and the volume flow rate Q=0.7 m s. Find the corresponding volume flow of a geometrically similar fan of 1 m diameter, running at 500 rev min at same conditions. Assume that the fan efficiency is unchanged. Ja
5
Lubricating oil is pumped to flow with velocity, V between two stationary paralle! plates separated by a thin gap of b = 1.8 mm as shown in Figure Q4. The gauge pressure at the inlet, Pn, is 100 kPa gauge. The pressure changes linearly to the atmospheric pressure at the outlet. Assuming the oil as an incompressible, steady and fully developed laminar flow of viscous fluid, detemine the equation of the velocity profile and the volume flow rate, Q. Calculate the Reynold number for the flow to justify that the flow is indeed laminar. [Lubricating oil properties: µ = 72.5 x 10° kg/m.s and p = 865 kg/m³] 1.0 m Pin y Pout 0.8 m V Figure Q4