The box drops a few centimeters starting from rest, and the surface has a coefficient of friction of 0.18. The weight of the box is 93 N and the The force exerted by the spring is 17 N. Enter the value of the force that causes the displacement.

Q: determine thelargest mass of block B without causing motion of the system

A: GIVEN :- mA=2kgμs=0.15let mass of block B: mB FREE BODY DIAGRAM :-

Q: of the slot on the cylind e the cylinder is in cont and slot at any instant. neces to om

A: Function relating the radius and angle made r= 0.6 θ ---- (1) Substitute π rad for θ in equationr=…

Q: The force P is applied to the 38-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The desk has a weight of 54 lb and a center of gravity at G. The coefficients of static and kinetic…

A: Given data  Weight of desk (W) = 54 lb  Coefficient of static friction (μs) = 0.5 Coefficient of…

Q: Determine the largest force P (to the nearest integer) which can be applied to the cord without…

A:

Q: The force P is applied to the 52-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The force Pis applied to the 49-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The force Pis applied to the 48-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The 472-N force is applied to the 84-kg block, which is stationary before the force is applied.…

A:

Q: the tension in the wire.

A: Given DataThe length of the wire L=55 mThe speed of the plane v=28m/sThe mass of the plane…

Q: The force P is applied to the 58-kg block when it is at rest. Determine the magnitude and direction…

A: Given data: ◆ The mass of the block: m = 58 kg ◆ The angle of inclination of plane: θ = 15° ◆ The…

Q: A bucket which has a mass of 910g when empty and contains 3 litres of water is swung round in a…

A: When a body rotates in a circle it experiences a outward force called centripetal force, which is…

Q: it is embedded into the wooden block. Which of the following is the maximum displacement of the…

A:

Q: Determine the force P needed to (a) impend the crate to slide up the 15° -incline plane (b) give the…

A: Given data:

Q: The force P is applied to the 42-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The tractor-trailer unit is moving down the incline with a speed of 4.3 mi/hr when the driver brakes…

A: Answer: The percent increase in the "hitch-force component which is parallel to the incline"…

Q: 4. The car has a mass of 1.6 Mg and center of mass at G. If the coefficient of static friction…

A:

Q: If the 40kg box is moving with 1 m/s^2 acceleration to the right, determine the magnitude of normal…

A: Mass of box, m=40kg Acceleration of box, a=1 m/s2 Force, F=174N Kinetic friction, μ=0.3

Q: The force P is applied to the 38-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: : A 5 kg block is pushed up along the slope as shown. The coefficient of kinetic friction is ?௞ =…

A:

Q: A rope of length L = 1.5 m and mass m = 2.3 kg is initially at rest and can slide on an inclined…

A:

Q: he conveyor belt is moving downward at 5 m/s. If the coefficient of static friction between the…

A: Given:v=5 m/sm=12 kgμk=0.71

Q: The force P is applied to the 41-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: A 100 pound pipe is at rest vertically, when the cable is connected to B at the force of P=50…

A:

Q: The pipe has a mass of 750 kg and is being towed behind the truck Egue 1) If the acceleration of the…

A:

Q: Q2/ Three blocks having masses of 5 kg , 10 kg and 15 kg are in contact on a fixed smooth inclined…

A:

Q: Q2/ The 150 box being pulled in 14 sec by the M winch M, If the winch efficiency is c= 0.65 and the…

A: Given :Mass of box,M=150Kg(unit assumed as not given)Power input,Pi=20KWEfficieny of…

Q: = 14 ft/s to 14.102 The 1-lb block is given an initial velocity vo the right when it is in the…

A: Initial velocity = 14 ft/s

Q: The 602-N force is applied to the 104-kg block, which is stationary before the force is applied.…

A:

Q: The force P is applied to the 61-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: A car bumper is designed to bring a 2,253-lb car to a stop from a speed of 4.9 mph while deforming…

A:

Q: A bicycle and a rider of mass 90 kg are travelling at the rate of 15 km/hr on the level road. A…

A: Given that,    Mass of bicycle and rider, m=90 kg    Speed of bicycle, v=15 km/hr=15×10003600=4.1667…

Q: Q2. Determine the magnitude and direction of friction torce acting on the 20kN block shown if P-10kN…

A: The magnitude and direction of the friction force. Given: The weight of the block is W=20 kN. The…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.