The boom derrick supports a suspended 15-kip load. The booms BC and DE are each 20 ft long. The distances are a = 15 ft and b = 2 ft, and the angle 0 - 30. The angle between BE and BC in 77.4". Þetermine the tension in cable AB and the reactions at the pin 1 BC à supports C and D.

Q: 3. Two cables are tied together at c and are loaded as shown. (u) Determine the tension in cable AC…

A:

Q: 0.8 m 800 N LC 0.8 m 600 N B 0.4 m 0.4 m A bent rod is supported by the roller at B, and the smooth…

A:

Q: B 4 2 A 200 KN 100 KN 7A.Find the reaction of the placement of the skeleton next to 7B.Determine the…

A: The support reactions can be calculated by considering the summation of vertical forces to be zero…

Q: 6F. The homogenous plate ABCD is supported by hinges along its side AB and by the cable ED.…

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: A thin rectangular plate that lies in the xy plane is supported by a cable and a bearing at point C.…

A:

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: For the following calculate the reactions at A and B. 2 kN-m 6 kN-m A 60° 2 m

A:

Q: 2. The rectangular plate is suspended from a ball and socket joint at O and two cables, as shown.…

A:

Q: A 1000 lb O 1160 lb O 1000 lb 12 ft B 360 lb/ft

A: To Find:- the vertical reaction at B

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A:

Q: Refer to the diagram. The roller at A is in a smooth slot. Determine the reactions at A and O.

A: for vertical equilibrium F1sin 55 + Ay = Ry1.258 * sin 55 + Ay = Ry   For Horizontal Equilibrium…

Q: B D - W 2W - L/2 L/2 * L/2 L/2

A:

Q: Problem 2 When force F is applied to the handle of the valve shown, its a moments about the x and z…

A:

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is…

A:

Q: C B 2 m 30° 3 kN 2 m A 4 kN - 2 m For the following truss system, determine the tension TAB in the…

A:

Q: The bars AB and BC of the frame shown are each of length L and connected by a pin at B in addition…

A:

Q: The cantilever truss shown is hinged at D and E. Find the forces in each members. 5 kN 60 60° 30 A E…

A:

Q: PROBLEM 1: Determine the tension in each cable and the components of force reaction at D needed to…

A: Given ,A force of 400 N is supported by two cables AB and AC.To Find - The tension in each cable and…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.