The block diagram of a feedback control system is shown in the following figure. Sketch the signal flow graph of the system. Explain Mason's gain formula. Obtain Y(s)/R(s) using Mason's gain formula. H3K RIG) 162 G3 Hz G4

Q: 1. Give the temperature classification for solid insulating materials. Why is this classification…

A: It is asked to give the temperature classification for solid insulating materials. Also we need to…

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: 5:1 I lo Vvms | RL the Arrdy , Azrddg, PLave ele

A:

Q: Grateful help with Part B please.  Thanks

A: Characteristic impedance is a property of the material that determines whether or not it can…

Q: What is OSHA mission?

A: -OSHA stands for Occupational Safety and Health Administration . It is for the U.S Department of…

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A:

Q: How IGBT is classified based on its layer of construction? Compare the characteristics of the device…

A:

Q: Grateful a little help with this homework thanks.

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: A high voltage transmission line transmitting 10 MW of power operates at a voltage of 105 KV…

A:

Q: Can you help me with questions two and three please?

A: Present StateNext State (UP)Next State…

Q: What is HT supply?

A: What is HT supply?

Q: where is it most convenient to find a PKES system

A: We need to tell about PKES .

Q: ity or enery that are used by

A: The power system consists of electric generation, distribution and customer satisfaction. In a…

Q: can i see the solution?

A:

Q: List and explain types of Fire Extinguishers. What's the difference between Mechanical safety vs.…

A: Both more formal visual inspections and routine, informal "before use" visual checks enhance safety.…

Q: 5 - What should be done first when a person being electric shocked seen? A) Cut off the electricity…

A: If we seen person being electric shocked then we need to do take some necessary action

Q: question: Suppose that you want to sort blocks of different heights automatically. How can this task…

A:

Q: What are the different onboard sources of electrical power in a modern commercial passenger…

A:

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: where is the value of 10/sqrt(2) coming from?

A:

Q: where did the 100 come from? Thank you.

A: In the given solution Xc<<1.5k Where Xc is  reactance of the coupling capacitor .

Q: This is a general question: How do smaller electrical engineering labs relate to building a…

A: Smaller electrical engineering labs can be very helpful in building a relatively larger system. This…

Q: Is there a way to clean up this answer by using proper notation

A:

Q: With the help of schematics, briefly describe, how a telephone set works.

A:

Q: What is meant by Electric Bid Package?

A: Bid package means the collection of the pertinent portion of the construction documents into a…

Q: 8. A larger time delay has been provided with over-voltage protection compared to the under-voltage…

A: Time delays are used to control the flow of power in different parts of the system and by…

Q: Can someone help in proposing a new or revised electrical gadget or device for safety purposes

A: Electrical device for safety purposes: Fuse: A fuse is an electrical safety device that has the…

Q: in this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  Legally Required standby systems provide electric power to selected loads during firefighting…

Q: List at least 5 research topics that are connected to Electrical Engineering.

A: 1. PM machines with high power and high speed  PM machines or Permanent Magnetic machines have…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.