The bent rod ABEF is supported by bearings at C and D and by wire AH. Knowing that portion AB of the rod is 250 mm long, determine; a) The tension in the wire AH. b) Reactions at C and D. Assume that the bearing at D does not exert a force of axial thrust.

The bent rod ABEF is supported by bearings at C and D and by wire AH. Knowing that portion AB of the rod is 250 mm long, determine; a) The tension in the wire AH. b) Reactions at C and D. Assume that the bearing at D does not exert a force of axial thrust.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Related questions

Q: A 200mm lever and 240mm pulley are welded to the BE shaft which in turn is supported by bearings at…

Q: 3. Determine all forces acting on member ABE of the frame shown. Note: D is a frictionless roller.…

Q: Solve Prob. 4.115, assuming that the hinge at A has been removed and that the hinge at B can exert…

A: Given data Load acting at the center of the plate= 300 lb Coordinates of the points are

Q: Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by…

Q: At the lower left end A of the bar, bent into an isosceles right triangle, a vertical force F is…

A: Please see the attached solution:

Q: Find: Support reaction at roller D ( forces in member BC, and EA, and specify if in tension or…

A: The free-body diagram of the above truss is shown below.

Q: A uniform circular rod of weight 8 lb and radius 10 in. is attached to a pin at C and to the cable…

A: Draw the FBD diagram showing the thin homogenous wire. Part a) Find the centroidal axis for the…

Q: The links AB and DE are connected by a bell crank as shown. Determine the maximum force that can be…

Q: Determine the components of the reactions at A and E if a 1.050 × 10³ N force directed vertically…

Q: 100 mm 100 mm 100 mm 540 N D. 225 mm B

Q: 6.83-A smooth pulley is attached to the member ABD as shown. Determine the forces in Pins D, B, A…

Q: The frame shown is supported by three cables and a ball-and-socket joint at A. For P = 0, determine…

A: To find: Tension in each cable The reaction at point A. Free body diagram of the frame:

Q: E 2. A force, P of magnitude 90 lb is applied to member ACE, which is supported by a frictionless…

Q: 3. For the frame shown, draw the FBD and determine the reactions at A and C D 200 N 450 mm 200 mm в…

A: F=200 N

Q: 300 kN 3 m D 5 m P kN 3 m 3m- Find: Support reaction at roller D forces in member BC, and EA, and…

Q: The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal…

A: Find outDetermine the tension in the cable AE.Given(I kip = 1000 lb)Load P = 2 kips = 2000 lbMoment…

Q: he 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

Q: 1.25 m N 1.25 m 3m 1.5 m E B G 5 kN 0.751 0.75 m X The rigid L-shaped member ABC is supported by a…

Q: A In the frame shown the member BCD is connected to member 6 kips 4.8 ft ACF by a smooth peg and…

Q: ray for the paper supply of a photocopy machine is shown. The tray is supported by a single hinge at…

A: Given-Information:- Weight, W = 14 ND = 190 mm To-Determine:- Reactions at point B

Q: The rectangular plate shown below weighs 100 lb. and is held in position by a cable EF and hinges at…

A: To find:The tension in the cable.The Reaction at A and B.Given:The weight of the rectangular plate…

Q: The press shown below is used to emboss a small metal plate at E. The press is composed of 3…

A: (a) Draw the free-body diagram of the system.

Q: Determine die maximum tension that can be developed in cable AB if the maximum allowable value of…

A: Given data Maximum allowable value of die reaction at C, R=250 lb. Draw the free-body diagram of…

Q: The 48-lb load can be moved along the line of action shown and applied at A, D, or E. Determine the…

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C…

A: Given data To determine the vertical force P exerted by the tower on the pin at A if the tension…

Q: 4 in. 5 in. C G 9 in.- E 45 lb D F -6 in.6 in.- B 120 lb

Q: I barrow. Knowit ion at the wheel) R = 50 i N, determ

Q: Q.3) A cylinder weighing 600 N is supported by a pin-connected two-bar frame. Determine the forces…

Q: 1. Forces of 900 N and 500 N are applied to member ACE which is supported by a frictionless pin at A…

A: Given data: The fore at point C is, 500 N. The force at point E is, 900 N. Calculate the angle…

Q: 2. A 200-mm lever and a 240-mm pulley are welded to the axel BE that is supported by bearings at C…

A: Taking moment about C∑Mz=0720200-T120=0T=720×200120T=1200Nso the tension in cord is 1200N

Q: The uniform (18 kg) bar OA is held in the position the pin and the cable AB. Determine Shown by %3D…

A: Consider the free body diagram shown below for the given system. Here,

Q: 2.The lever BCD is hinged at C and is attached to a control rod at B. If P = 200 N, determine (a)…

A: Given data: P = 200 N Need to determine the tension in the rod and reaction at point C.

Q: A person's arm is used for ergonomic studies. If the distance of the AB, BC, and CD segments are…

A: The loading diagram of the given ergonomics study considered is as shown below: Find the…

Q: is supported at the left end 6-86 Beam CD of Fig. C by a smooth pin and bracket and at the right end…

A: Given Applied load = 5 kN To find Reaction at C Force in cable when load is applied

Q: A force P is applied to a bent rod ABC , which may be supported in four different ways as shown. In…

A: Draw the F.B.D of the part a of the system. For the Equilibrium of the member. For the equilibrium…

Q: A force P is applied to a bent rod AD that may be supported in four different ways as shown.…

A: Given:- Force P at mid of AC AC=2a CD=a θ=45° To find:- Reaction forces at supports

Q: The press shown is used to emboss a small seal at E. Knowing that the vertical component of the…

A: (a) The free-body diagram of the press is given as, The reaction at the seal will be a vertical…

Q: 1.8 m 1.8 m B 2.1 m C 1.8 m. 1.2 m 4 kN

Q: 4.88 Rod AB is bent into the shape of an are of circle and is lodged between two pegs D and E. It…

Q: The frame shown supports a mass of M = 49 kg. Knowing that L = 0.45 m determine the reactions at A…

A: The free-body diagram for the system BC.

Q: 5.82 The tension in cable AB is 800 lb. Determine the reactions at the fixed support C. N 4 ft F -4…

A: The tension in cable AB is

Q: A torce Pot magnitude 120 lb is applied to member ACE, which is supported by a frictionless pin at…

A: Consider the free body diagram is given as,

Question

The bent rod ABEF is supported by bearings at C and D and by wire AH. Knowing that portion AB of the rod is 250 mm long, determine;
a) The tension in the wire AH.
b) Reactions at C and D.
Assume that the bearing at D does not exert a force of
axial thrust.

H
B
30°
250 mm !
D
250 mm
300 mm
50 mm
50 mm
400 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Free Body Diagram

Step 2 Calculation

Step 3 Calculation

Step 4 Calculation

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

28 cm a? 100 cm 30° 15 cm
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 1.475 O 1.030 2.950 B 4.00 O 1.450 O 1.500 1.000-1.010 .010M ABM 2.00 A
30° 20 kN 25 kN y 5 m 3 m 6 m 3 m 30 kN
1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At which point(s) of the cross-section the normal stress is zero? b) Determine the maximum compressive and tensile bending stress in the beam.
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 O 1.475 O 1.450 O 2.950 O 1.500 O 1.030 4.00 0.010MABM 1.000-1.010 2.00 A
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)
250cm+10m
300 N 36 mm 12 mm 120 mm В 30 mm A C D 6 mm 96 mm 42 mm| 30 mm 300 N
10 cm| 10 cml -20 cm B A 20 cm
P1.60 A block of weight W is being pulled over a table by another weight Wo, as shown in Fig. P1.60. Find an algebraic formula for the steady velocity U of the block if it slides on an oil film of thickness h and viscosity u. The block bottom area A is in contact with the oil. Neglect the cord weight and the pulley friction. Assume a linear velocity profile in the oil film.
100 mm В A 30 mm