The below figure shows the electric system in a mild HEV (such as 48V B-ISG or BAS), explain: What type of power electronics device (rectifier, inverter, buck, boost, or ...) is needed between these two voltage systems (48V and 12V)? 12V 48V Power 12V Load 12V Starter/ (Cold Crank) 48V Starter/ Battery Generator Load 48V Load 12V 12V Electronic 48V 48V Load Battery Device GND GND

The below figure shows the electric system in a mild HEV (such as 48V B-ISG or BAS), explain: What type of power electronics device (rectifier, inverter, buck, boost, or ...) is needed between these two voltage systems (48V and 12V)? 12V 48V Power 12V Load 12V Starter/ (Cold Crank) 48V Starter/ Battery Generator Load 48V Load 12V 12V Electronic 48V 48V Load Battery Device GND GND

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

THREE PHASECONTROLED RECTIFIER It is used to feed a physical load which is resistance of 6 ohm And inductive impedance high enough for the current to be continuous and free from vibrations and the THREE PHASECONTROLED RECTIFIER is connected to delta and his voltage 100 volt , What is the value of the power drawn from the source if the ignition angle is 45 degrees?
Explain power electronics convertors for solar systems
Calculate the following a) V1 [1 b) i c) i2 Q17 The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. i) Calculate the average de current through the load resistor 3KQ. Calculate the value of input ac power, output de power. 18. For the circuit shown in Figure B18, Vcc = 18 V, B = 110, Rc = 4.7 kQ and RB that VBE=0.7 V. 450 k2, assum %3! Vcc | Ic Ro RB Vc VCE
A half-wave rectifier with a reservoir capacitor is connected to an AC mains supply(220Vrms, 50Hz) via a 20:1 transformer. What value of the capacitor is needed forthe ripple voltage of X% of the peak input voltage? The load takes a maximum currentof ???? mA. X= 12% mA = 160
design a controlled three phase rectifier
In a DC machine, rectification process is carried out in order to get unidirectional output (DC). This rectification process is carried out by a) Half wave rectifier b) Full wave rectifier c) Mechanical rectification d) Centre tapped rectifier
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
If the load resistance of a capacitor-filtered full-wave rectifier is increased, the ripple voltage Select one: a. increases b. doubled c. has different frequency d. not affected e. decreases
A Half-wave rectifier has No Load DC Voltage of 10 Volts and the same half- wave rectifier has a full Load DC Voltage of 4 Volts. Find the regulation factor. Note: Require answer in TEXT FORMAT!!
Asap, answer within 1 hour.
design a uncontrolled single phase rectifier