The beam supports a distributed live load of 2 kN/m and single concentrated load of 6 kN. The dead load is 4 kN/m. Determine (a) the maximum vertical positive reaction at C, (b) the maximum negative moment at A. B C- -3 m- -3 m 3 m

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A:

Q: Replace the 30-kN force acting on the steel column by an equivalent force-couple system at point O.…

A:

Q: 10 kN -0.6 m 0.6 m- 08 m 6 kN 60 0.4 m

A:

Q: oblem 2 e truss shown carries the following uniform live load and concentrated e load. E G D 3 @4 m…

A:

Q: Draw the influence line for shear force Vc. Enter the magnitude of your and G influence line when…

A:

Q: Determine the reaction at the supports A, C, and E of the compound beam. 3 kN/m 12 kN

A: Given : Determine reaction at the support A, C and E ?

Q: 1) Determine the reaction at pins A and D for the frame and distributed load shown

A: Given a frame with Uniformly varying load and it is asked to find reactions at pin support A and…

Q: 3. For the system shown, a. Determine the equivalent force-couple system at the base at C. Express…

A: Determine the equivalent forces-

Q: Determine the internal bending moment acting at point C. A -24 kN-m 24 kN-m 36 kN-m O 48 kN-m 4 m 12…

A:

Q: C-2 A uniform live load of 300 lb/ft and a single live concentrated force of 1500 lb are to be…

A: Given data:- The given uniform live load, =300 lb/ft3 The concentrated force, = 1500 lb The given…

Q: The beam is supported and loaded as shown. Determine the reactions at hinge A and roller B.

A: ###Determination of Reaction  at Hinge A and Roller B####

Q: Replace the 21-kN force acting on the steel column by an equivalent force-couple system at point O.…

A:

Q: Civil Engineering Question

A:

Q: 4m 4 m B

A:

Q: 2-10. Determine the components of reaction at the fixed support D and the pins A, B, and Cof the…

A:

Q: 5 kN /m A 10 KN zm 3m

A:

Q: Q2. Draw the influence lines for the vertical reactions at supports A and B and moment at A of the…

A: ILD : Influence line diagram ILD represents variation of stress function when a unit concentrated…

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: Draw the influence line for (internal) bending moment MA. Enter the magnitude of your influence line…

A:

Q: Determine all the reaction components at supports A (fixed) and B (hinged), Joint C and D are…

A:

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: ermine the reaction at support A and B. Support A is pin while support B is roller. 6 kN 6kN 12EN-m…

A:

Q: Beam ABCD carries a varying load on segment AB as shown below and a counter clockwise couple at…

A: Find reaction at A

Q: 4. For the compound beam and loads as shown, find (a) the maximum reaction at C (b) the maximum…

A: I have solved this problem in detail although I have used it by logic and by self inspection which…

Q: Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the right of the…

A: Given data in question  Overhanging beam  Dimension = 9 m long To find out  ILD for RB , RA+ &…

Q: For the beam shown, determine the reactions at A, B and D. At B, C and D is a pin and at A is a…

A:

Q: Determine quantitatively the influence lines for Ay, ME and VẸ for the statically determine system…

A: Data given: Asked: Influence lines for Ay, ME and VE

Q: 3. The distributed loading acts on the simply supported beam. The support at A is a pin and the…

A: A simply supported beam with hinged support at A and roller support at B with an equal overhang of…

Q: 4. Determine the support reaction at A and B for the given beam. l0 kN 20 kN A 3M 5M 3M B

A:

Q: B A+B ce line for the vertical reaction at A, what is the maximum ordinate? what is the ordinate at…

A:

Q: A unit load will pass in the simple beam shown. 1) The absolute reaction @ A and C when the unit…

A:

Q: For the simply supported beam shown, draw influence lines for moment at C (12-ft from support A),…

A: when the unit load at A and B then bending moment at C equal to 0 .and if the unit load at C then…

Q: The truck has a mass of 4 Mg and mass center at G1, and the trailer has a mass of 1 Mg and mass…

A: To get maximum bending moment heavy load must be placed such that heavy load and the resultant of…

Q: The beam is subjected to a uniform distributed live load of 5kN/m, a uniform distributed dead load…

A:

Q: Draw the influence line for the force in member BF, then determine the maximum force (tension or…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.