The beam is supported by the three pin-connected suspender bars, each having a diameter of 0.5 in, and made from A-36 steel. The dimensions are a = 6 ft and b = 4.5 ft. Part A Determine the greatest uniform load w that can be applied to the beam without causing AB or CB to buckle. Express your answer to three significant figures and include appropriate units.

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: answer the next part pls

A: From the previous solution: Pitch circle diameter→D=4 inch Number of teeth→T=16 Hence the circular…

Q: solution incorrect resolve again

A:

Q: resolve solution

A:

Q: draw the left side

A:

Q: how does F_BC equal 6

A:

Q: Says.003 is wrong

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Identify the 'R15' in the given picture R15

A: In the engineering drawing Hidden lines The hidden line is represented with the dashes about 1/8"…

Q: Answer in number 7 and 8.

A:

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: Please give the answer as in the format asked

A:

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: can u pls solve the question using hand written notes in detail and figure

A:

Q: . Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: According to the given details provided, we need to identify the view on the right that shows the…

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Give a steps by steps answer of the solution

A:

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: F -L/2 -L/2 k

A: The total deflection of a beam under load F is equal to compression due to spring and elastic…

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Note: As per the policy, we can solve the first question from the multiple question. Please,…

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top…

A:

Q: Draw the 1st and 3rd Angle Orthographic sketch of the following part:

A: According to the 3d object provided in question three orthographic view is drawn with the help of…

Q: Find degree of freedom.

A:

Q: 3-5.22. Bar AB of negligible weight is subjected to a vertical force of 600 lb and a horizontal…

A:

Q: Use basic drawing instruments (pencil, scale, protractor, compass, etc). The Front View of a line AB…

A:

Q: Question 16 Here is a way we can estimate the distance from the earth to the moon. When the moon is…

A: GIVEN DATA- Arc Length AB=6152 miles The radius of earth R=3960 miles We have to find both point…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.