The beam is constructed from two boards fastened together at the top and bottom with three rows of nails spaced every 8 in. as shown in. F = 8 in. lb s in Part A If an internal shear force of V = 1000 lb is applied to the boards, determine the shear force resisted by each nail. Express your answer in pounds to three significant figures. ANSWER: 9 in. 2 in. 4 in.

Q: A prestressed beam is given in the figure below. X Aps = 696 mm2 H = 540 mm B = 350 mm y = 90 mm L =…

A: Area of steel, Aps=861 mm2 H=560 mm B=350 mm y=110 mm Initial pre-stress, fps=1208 MPa

Q: The beam is constructed using 2 boards and 3 rows of nails spaced equally. A shear force is applied…

A: The moment of inertia

Q: The distance of line AB was measured four times and recorded as follows: TRIAL DISTANCE (m) 1 102.1…

A: Following are the given 4 measurements: Trial Distance (m) 1 102.1 2 102.3 3 102.2 4…

Q: Show FBD and complete solution.    The system of knotted cords shown in the figure support the…

A: To find tensile force in each rod

Q: Express each force as a Cartesian vector and calculate the resultant force.

A: Given:- Forces;              Determine:- Resultant force using Cartesian vector.Cartesian Vector:-…

Q: No. 9 bars compression bars in a column are to be lap spliced. There is no excess steel and the bars…

A: Given,  Compression bar no. #9 is spirally reinforced with dia 3/8 inch and pitch 3 inches.…

Q: Take P₁= 5 kip and P₂ = 2.5 kip. (Figure 1) Figure 1 of 1 |||| Determine the absolute maximum shear…

A:

Q: PDE = 2000 lb A₁ = 2000 lb 19 B 119 A 119 D 4 A 40 K G 3000 lb 1000 lb = 4000 lb (b)

A:

Q: O Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A:

Q: A reinforced concrete rectangular beam has dimensions 18" wide by 26" deep and is subject to loads…

A:

Q: Q3 - For the given wooden beam and cross section, a) Determine the maximum magnitude of P (P>0) by…

A: To determine: a) The value of maximum magnitude of P. b) The value of maximum spacing of nails.…

Q: ly- f= 6,000 psi • As = 7.07 in? • b = 16 in • d= 30 in a) Compute the depth of the compressive…

A:

Q: Problem 10. DETERMINE THE DIMENSION FOR THE PLYWOOD BOX BEAM FIGURE SHOWN. y = A1 = 21 x 4.5 41 = A₂…

A: Given data:- The expression Area A1=21X4.5 The expression Area A2=(21-6)×3.5=15×3.5

Q: The bolt is subjected to the force F. which has components acting along the z. y, z axes as shown.…

A: Given : F = 76 N Alpha = 52 degree Gamma = 50 degree To Find : Determine the angle beta and then…

Q: A horizontal force of P = 45 kN is applied to joint Cas shown in (Eigure 1). Each pin has a diameter…

A: Shear stress is the force that tends to cause deformation of a material by sliding along a plane.…

Q: NEED ASAP

A: The given data is shown below: Strain=0.075Diameter=3.592 mmDeformed length=891.308 mmModulus of…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.