The beam cross section below is idealised into booms and thin skins. The section is symmetrical about the y axis. It is a closed section but an imaginary cut has been made on the left hand side in order to find the q, distribution. A shear force of S; is applied. The shear flow is constant between the booms and the q, components are shown in the shaded blocks (with direction). The constant component, qo is also shown. b.. 902 2.5a S The following values are known: Sz = 626 N a = 68 mm b= 85 mm qb1 = qb2 = 2A Use these to calculate the value of go in the (anticlockwise) direction shown. Enter your answer as N/mm, to 3 significant figures, but without the unit. You have a 3% margin of error.

The beam cross section below is idealised into booms and thin skins. The section is symmetrical about the y axis. It is a closed section but an imaginary cut has been made on the left hand side in order to find the q, distribution. A shear force of S; is applied. The shear flow is constant between the booms and the q, components are shown in the shaded blocks (with direction). The constant component, qo is also shown. b.. 902 2.5a S The following values are known: Sz = 626 N a = 68 mm b= 85 mm qb1 = qb2 = 2A Use these to calculate the value of go in the (anticlockwise) direction shown. Enter your answer as N/mm, to 3 significant figures, but without the unit. You have a 3% margin of error.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show FBD
Answer ASAP. I will rate Positively. Solve all parts
Q1: It is required that the resultant force acting on the evebolt in the Figure to be directed along the positive x axis and that F2 have a minimum magnitude. Determine this magnitude, the angle 0, and the corresponding resultant force. F, - 800 N 60 F2
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
A hollow steel beam (cross-section shown in figure 5) is subjected to a vertical shear force of 30 kN.Moment of inertia of the cross is IN.A = 383.33x106 in4.a) Solve to determine the maximum shear stress and its location.b) Solve to determine the shearing stress at fiber 75 mm from the top of beam’s cross-section.
Please answer fast and correct. I will hit the like. Don't copy from other site.
HI! HELP ME WITH THIS PLEASE. THANK YOU VERY MUCH!
Handwritten answers only pls.
Using stress transformation equation
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
PROBLEM # 3: Use the conjugate beam method and determine the slope at B and the displacement at C of the beam. "EI" is constant. 2 A В a a a a
Determine the the conjugate beam method ÁB = 0.2m El = constant %3D A.