Answered: The beam carries the loadings as shown…

The beam carries the loadings as shown in the figure. There is an internal hinge located at point B. Determine the internal normal force, shear and bending moment at D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

02 The truss gusset plate is subjected to the forces of three members. Determine the tension force in member Cand its angle a for equilibrium. The forces are concurrent at point O. 10 KN IS AN
Pin jointed frame is subjected to the external loads of F6 = 2502 N at D and F7= 1588 N at C as shown in Figure T2. Take the length of frames indicated as: L6 = 1665 mm and L7= 9342 mm. (). Draw the free body diagram of the given Frame/Truss; (6). Estimate the support reactions; (i). Determine the forces in all members indicating the nature of forces; (w). Verify the forces in members AD and AE by another suitable method. F6 F7 L6 60° 60° 30° B E L7
Part E The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T = 585-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. Determine the resultant bending moment in the y direction on the cross section at C. Express your answer to three significant figures and include appropriate units. HA Figure 1 of 1 (Mc)y = Value Units Submit Request Answer 400 mm 150 mm 150 mm Part F В 200 mm Determine the resultant bending moment in the z direction on the cross section at C. 200 mm Express your answer to three significant figures and include appropriate units. 300 mm 80 N 80 N HA 200 N 200 N (Mc)z = Value Units Submit Request Answer
Solve B Please fast
Please solve these two subparts with a proper steps.
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D
Draw the shear force diagram and the bending moment diagram of the bridge girder shown below. FAC = 84.1K (T) Fec 84.1K (T) FCD=64.7 K (c) 5 ft A 12 ft- 80 k D C 12 ft B
Determine the forces in given (S, ,S „S,and S) members for the plane truss system in the figure.All of the acute angles between the members of the truss system is equal to 60°, the angle between the horizantal line and link bar supported at point C'is equal to 30°. 2m- + 4X kN 4X kN 4X kN O G 2m 30 B C
The girder in the frame is subject to a uniform load of w = 4060 N/m over its length L = 9.80 m. a) What is the approximate moment in the girder at the face of the column at C? Use the standard sign convention for beams. MC = ? b) What is the approximate maximum positive moment in the girder? Mmax = ?
QUESTION 1. Determine the reaction at pins at A, B and C and fixed support at D. Answer in component form. Take P = 8+ 0.5(third highest digit of your student number). ALSO, draw the shear and moment diagram of member BC only. 12P kN 8P kN B 4 m D -3 m 3 m- 3m 3 m-
Compute the support reactions of the given beam below. Also, determine the maximum value of the positive and negative shear as well as the moment. Note: pt. a is hinge support, pt. b is roller support, pt. c is internal hinge support, pt. d is internal roller support, pt. e is roller support, and pt. f is a hinge support. Hint: Try to expose the internal reaction/s of the internal hinge support at pt. c as well as for pt. d internal roller support. For the units, the forces are in kN, then for the distances, take it as meters
How to get the shear force V= -P and the bending moment M= -Px