The bars of the pinned-connected truss shown in Figure below are each 30 mm by 60 mm in cross-sectional area. If the working axial stresses are 100 MPa for members in tension and 80 MPa for members in compression, what is the maximum load P (kN) the truss structure can carry based on the given stresses? ... B 8 m 6 m 10 m

The bars of the pinned-connected truss shown in Figure below are each 30 mm by 60 mm in cross-sectional area. If the working axial stresses are 100 MPa for members in tension and 80 MPa for members in compression, what is the maximum load P (kN) the truss structure can carry based on the given stresses? ... B 8 m 6 m 10 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Beam CX is subjected to a loading condition as shown in the figure. What will be the (a) the maximum tensile stress and (b) the maximum compressive stress in the Beam CX if its cross section is a T section with the given dimensions.
A 26-foot-long structural steel bar is being tensed along its centroidal axis. Point B is being tensed by 180 kips of force and point C is being tensed by 121 kips of force. The bar has a rectangular cross-section with a height of 3.6 inches and width of 2.8 inches. The steel is HSLC steel with a yield stress, oy = 50 ksi and modulus of elasticity, E = 30,000 ksi. Show all work and any assumptions clearly. Record your answers on the answer key. Complete the following: ): Calculate the axial stress in sections AB and BC of the beam. Does the calculated stress in either section exceed the yield stress of the steel? Calculate the deformation in sections AB and BC of the beam. What is the total axial deformation that the beam experiences? What is the final length of the beam? Calculate the factor of safety that this structural bar was designed for. w = 2.8 in. A B 180 k C 121 k Answer Key σ > Gy Yes or No * 18 ft 8 ft Axial Section Stress (ksi) AB BC Total Deformation, 8 (in) Final Length…
Q3: For the assembly shown in Fig. Q3. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Steel Bronze Aluminum B C A D P ЗР 4P +2P | 1m 2m 1.5m A= 480 mm? A= 650 mm? A= 320 mm? E= 200 GPa E= 83 GPa E= 70 GPa Fig. Q3
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure P-211 Aluminum A = 320 mm² 1.5 m 2P
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter rivets placed in a zig-zag pattern. The pitch of the rivets is 75 mm and gauge is 60mm. If the allowable tensile stress is 150 MPa, the maximum tensile force that the joint can withstand is
I need an answer ASAP. Ty
3. An aluminum bar having a cross-sectional area of 0.25 sq. in. carries the axial loads applied at the positions shown. If E = 10 x 106 psi, compute the total deformation of the bar. 8000 lb 3000 lb 7000 lb 2000 lb 5'- 4' + 3'→
An open-link chain is obtained by bending low-carbon steel rods of 0.5-in. diameter into the shape shown (Fig. a). Knowing that the chain carries a load of 160 lb, determine (a) the largest tensile and compressive stresses in the straight portion of a link, (b) the distance between the centroidal and the neutral axis of a cross section. 160 lb 160 lb -0.5 in. 0.65 in.
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P