The axle of the freight car is subjected to a wheel loading of P = 29 kip 60 in. 10 in. 10 in. P

Q: Ball joints connect the ends of each of the struts as shown. The resulting structure supports a…

A: Given: The variable, a = 6.6 cm The variable, b = 12.4 cm The variable, c = 12 cm The variable, d =…

Q: he shaft, shown below, consists of rods AB and CD and a tubular segment BC. The rods are onnected…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: Q.2 Is this roll bar set to full 'stiff' or full 'soft'?

A: Solution:   The correct answer with necessary explanation is given below:

Q: 8. Plot a graph of the internal axial forces in segments AB, BC and CD vs. distance measured from A…

A:

Q: Part A The crate shown in (Figure 1) has a mass of 105 Kg and center of mass at G. If the…

A: GivenM=105kgμs=0.20

Q: An eighteen-wheel truck is rated at a gross (total) load carrying capacity of 260,000 lbs (including…

A: Given data  Total load = 260000(lb) Contact area = 12"×12" Find the tire pressure required to carry…

Q: If during the application the bearing subjected to an equivalent radial load of 1.07 kN, and the…

A:

Q: Email: al azzawwi@uomisan.edu.iq Assist Lec. Dr. Ali H. Hasan 0.4. Determine th Q4/ Arm ABC acts as…

A:

Q: Determine the magnitude of the pin force at A. Modification: Change the load to 3,50 Ibs, the…

A:

Q: Identify the zero force members by circling the appropriate options in answer block 1. The truss is…

A:

Q: he parallel component load P to the incline surface is given 400 lbs. calculate the value of the…

A: Given: Load of P acting to the body at the inclined surface,

Q: Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the…

A: Given Data

Q: DETAILS SERPSE10 12.3.OP.004.MI. kg automobile has a wheel base (the distance between the axles) of…

A:

Q: A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The…

A: Introduction: A brake is said to be self emerging brake when the moment due to friction act in the…

Q: * 1. The light bar is used to support the m kg block in its vertical guides. If the coefficient of…

A: (a) Draw the free-body diagram of the block. Apply force equilibrium in vertical direction.…

Q: The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular…

A: We have to determine smallest distribution load.

Q: The wagon has a mass of 19.5 kg and centre of mass at G. Both the front and rear wheels are locked,…

A:

Q: A rear-wheel drive vehicle is traveling at 57 mi/hr on a level surface with a coefficient of…

A: The speed of the rear-wheel drive vehicle: ν= 57 mi/hr = 83.6 ft/s The coefficient of adhesion:…

Q: 3. What is the minimum static coefficient of friction required to maintain the bracket (light…

A: Consider the free-body diagram for the system as shown below.

Q: A plank L m long is placed in a horizontal position with its ends resting on two inclined planes as…

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a 2.9 ft, b-2.4ft, r - 6 in. "" W…

A:

Q: Calculate the frictional force developed between the block and the plane. Given P=225 N , W= 691 N,…

A: We have to determine

Q: 3. In the given 15.0 meter slab and inclined 10°with the horizontal, the ends are resting on…

A:

Q: Consider the arrangement of a simple band brake as shown in the figure. Determine the brake torque…

A:

Q: Compute the 1. force in each member. 2000 lb 3000 1b

A:

Q: For the drum brake figure shown below a) If a couple M of magnitude 1xy N.m is applied to the drum…

A: (a) Free body diagram the fig I and fig II showing the free body diagram of drum brake shown below…

Q: 3.32 10 KN 2m C 2.5 m 2. 1.33m

A:

Q: he wheel is subjected to a torque of M-55 N-m. The oefficient of kinetic friction between the band…

A:

Q: An axial load of 160 lb is applied to the end bear- Fig. ses place over an annular ring of radius 4…

A: Given that, Axial load applied, P=160 lb,Inner radius of ring, r=4 in,Outer radius of ring, R=7…

Q: plank 25 meters long is placed on rough inclined planes at an angle of 15 ̊ with the horizontal as…

A: In the system there are 4 fources, RA, RB, 350 N and 75 N. First of all do force balance along the…

Q: (Jeep Commander approximately has the following specifications Q3 mg = 5091 lb | = 109.5 in , a1=…

A:

Q: Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the…

A: Given Data

Q: The wheel shown supports a load of 500 lb. The hub fits loosely over an axle of diameter 1.3 in and…

A: Given :To find:

Q: A flywheel of radius 0.1 m which is attached with a mass of 800g takes 12 seconds for 2 revolutions.…

A:

Q: 19. What is the equilibrium angle if the 1-1bm rod is 24 in long? Assume all surfaces are…

A:

Q: The mine car and its contents shown in (Figure 1) have a total mass of 4.5 Mg and a center of…

A:

Q: A plank 25 meters long is placed on rough inclined planes at an angle of 15 ̊ with the horizontal as…

A:

Processing of Polymer Matrix Composites

The polymer matrix composite is described as a composite material that contains some polymer in the form of either fibers or powder. Polymer matrix composites are also known in short as PMC's.