The assembly in Figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support ? 0.75 m 1.5 m B Steel A = 250 mm2 E = 200 GPa Aluminum L- 2 m A = 300 mm2 E = 70 GPa

The assembly in Figure below consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support ? 0.75 m 1.5 m B Steel A = 250 mm2 E = 200 GPa Aluminum L- 2 m A = 300 mm2 E = 70 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A submarine robot explorer is used to explore the marine life in deep water. The weakest point in…

A: The maximum pressure hold by the weakest point on the submarine is given as, P=300 MPa=300×106 Pa

Q: Instruction: Determine the moment of the force about point 0.

A: Given data as per question

Q: If the magnitude of the resultant force acting on the bracket is to be 550 N directed along the…

A: In basic terms, magnitude means 'distance or amount.' It depicts the absolute or relative size or…

Q: I am lost as to where the 2560.89 came into the equation?

A: The preceding method describes how to calculate the time when the centripetal acceleration of a bike…

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500 N load.…

A: Given data weight =500N Considering FBD of the system Considering vertical forces equlibirium…

Q: If cable AD is tightened by a turnbuckle and develops a tension of 1000 N, determine the tension…

A: Consider E is the origin. From the given diagram, the coordinates of A, B, C, and D are (0, 0, 30…

Q: : Determine the moment of the force about point A.

A: Given: TO determine: Moment about A

Q: A square high-density polyethylene [α = 158 × 10–6/°C] plate has a width of 450 mm. A 270 mm…

Q: Describe another fundamental principle that relates to the central limit theorem and describe how it…

A: Central limit theorem: This theorem states that the distribution of the samples from a population…

Q: can I ask for a detailed solution for the system of equations?

Q: Structure and Injecting Energy

A: The concepts of "Structure" and "InjectingEnergy" These terms can have various meanings depending…

Q: The bracket is subjected to the two forces shown. Find the magnitude and coordinate direction angles…

A: Given F1 = 250 N F2 = 400 N To find Resultant Direction of the resultant

Q: A package of frozen fish sticks have different instructions when they are heated up on the stove as…

Question

I need the answer quickly

The assembly in Figure below consists of a light rigid bar AB, pinned at O,
that is attached to the steel and aluminum rods. In the position shown, bar AB
is horizontal and there is a gap, A = 5 mm, between the lower end of the steel
rod and its pin support at C.
Compute the stress in the aluminum rod when the lower end of the steel rod is
attached to its support ?
0.75 m
1.5 m
B
Steel
A = 250 mm2
E = 200 GPa
Aluminum
L= 2 m
A = 300 mm2
E = 70 GPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

give a steps by steps explanation of the solution
Handwriting not allow please And give me complete answer
LESSON: AUTODESK FUSION 360 Choose from the choices below:
Solve show all steps and solution. Energy systems engineering
can you solve part B without just using those tables to find the answer?
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
hints: The ﬂask will be filled with water (at a constant rate of 500 gallons per minute). It will take me exactly 10 minutes to escape from the chains. The diameter of the tank at 1 foot intervals. I am 5 feet 9 inches tall, and I'm pretty skinny so that you can ignore both my volume and the volume of the stool in your analysis. A gallon is equal to 0.13368 cubic feet. You can think of the volume and the height of the water as functions of time. You can easily find an expression for V (t), and then use your expression for volume in terms of height to solve for h(t). after 10 minutes amount of water in the tank=66.84 ft3 t=69.3 minutes h(t)=e66.84t/100? -1 h(10)=e66.84(10)/100? -1=7.39 ft Height of stool=1.64 ft Height of water in the tank=7.39 ft Questions: show work How fast is the water rising? I would like to know how long I will have to hold my breath during the last part of the stunt.
P-4 Please I need help with this question needed very clearly and step by step explanation and needed with clear handwriting please, will be really appreciated for your help
Don't submit the wrong solution.
1. “The grain size of metal sheet influences its formability in two opposing ways. The yield strength of a metal increases as the grain size decreases. So, the formability of a component may decrease if the grain size gets too small. Larger grained metals have better formability, but the roughened surface that results from stretching metal with grain sizes that are too large is unacceptable for many applications. During a recrystallization anneal new grains form in the metal. The final grain size depends on the annealing temperature and annealing time.” As shown in the figure below (1"x1" area under a 50Xmagnification microscope), a cold-rolled metal has been annealed at 550 degrees C for one hour. Calculate the ASTM Grain Size Number for the following condition: image attached
Topics: Statics of Rigid Bodies, Equilibrium of Rigid Bodies, Equilibrium in Two Dimensions, etc. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” THANK YOU FOR YOUR HELP. PS: If you have answered this already, don’t answer it again; give chance to other experts to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times. If you answer it again, i'll dislike all your entries/answers.