The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.

The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flexural member is fabricated from two flange plates 1/2in x 16in and a web plate 1/4in x 20in. The yield stress of the steel is 50 ksi. a. Compute the elastic section modulus S and the yield moment My with respect to the major principal axis. b. Compute the plastic section modulus Z and the plastic moment Mp with respect to the major principal axis.
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
3. A flat steel bar, I inch wide by 1/4 inch thick and 40 inches long, is bent by couples applied at the ends so that the midpoint deflection is 1.0 inch. Compute the stress in the bar and the magnitude of the couples. Use E 29 x 106 psi. (Practice at Home) M 20" Cross Section P-1 20" 1/4" M
Solution w/ FBD
(N) 32900
3- Determine: m 0.4m a) The stresses in the bars shown after a temperature rise of 96°C. Brone har Ahunknan bar A-1500man A-1500mm E-10SGPa E-TGP -21.6 21 b) the corresponding change in the length of the bronze bar.
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
Please show a detailed solution and explanation including its FBD. Thank you!
I need the answer as soon as possible