The appropriate diameter is mm.

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Expandable pattern is used in ?

A:

Q: How can a bore be measured ? Please answer it fast.

A: Dear Students The answer is given in the below attachment

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: what metric pipe size is approximately equivalent to a U.S. customary pipe size of 3/4"?

A: 34'' means 34 inch

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: If the main scale reading (mm) and vernier scale reading (division) are 27 and 47 respectively for a…

A: Given: main scale reading = 27mm vernier scale division = 47 division total division on vernier…

Q: what is the MMC of shaft dimension 1.375 /- .030?

A: Given: The dimension of shaft  is 1375/-0.30 MMC :MMC stand for  Maximum Material Condition.

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: How can a bore be measured?

A: The inner diameter of any cylindrical device is known as bore. The inner diameter of the cylinder is…

Q: Draw chalk diagram of all sections

A: To draw section views

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: Try square is a measuring tool used to measure the straightness and squareness of a workpiece.…

A: The square of the measure consists of two main elements, the blade, often referred to as a beam or…

Q: A mass of 25 lb is applied at the end of a 2-inch-diameter rod shown in Figure P2. If the modulus of…

A:

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Find the depth of thread in mm for an external thread, if the pitch is 5 mm. Depth of thread (in mm)…

A: Given : Pitch (p) = 5mm   To find : Depth of thread (d) =?

Q: The . . nut is a hexagonal nut with ......e ... washer. dome flanged . cap square The of an object…

A: Let's discuss the types of nuts:- Dome nut means the dome head at the top of the nut. That's why it…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer.   The…

Q: 25 divisions with 34 divisi

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Can you put all the measurements, as in all measurements and make it in centimeters?

A: given : Isometric view

Q: what is the bottom length?

A: To calculate the bottom length

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: Outside calipers are used for measuring diameters of holes. Select one: True False

A: Outside calipers are used for measuring diameters of holes. Answer: False

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: What is the diameter of the groove?

A: Let us discuss given engineering drawing to find diameter of groove.

Q: Read the following inch vernier caliper setting 8. 1/128in

A: Solution:

Q: 0le A. An outside caliper can be used to measure the diameter of a

A: Caliper is used to measure the linear dimension, diameter of a hole and outer diameter of a shaft.…

Q: What was the orginal size of the smallest outside diameter?

A: Data given-

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

A:

Q: The denomination for a force or shrink fit in the US system is ?

A: Solution:

Q: 2. How far apart (in degrees) are the equally spaced drilled holes? 3. Define the dimension 3" XS BI…

A: Disclaimer:Hello. Since you have submitted multiple questions, we will answer the first two for you.…