the angular velocity of the hammer immediately after the

Q: Carriage is mounted on the outer guide ways of lathe bed and it can move in a direction parallel to…

A:

Q: If the particle is projected vertically upwards, it travels against the. O a. Gravitational Force O…

A: Given: If the particle is projected vertically upwards, it travels against the ......

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: Distinguish nominal diameter and gross diameter of bolt

A: Nominal diameter:Nominal diamater can be described as the pitch diameter of the thread of the…

Q: When the car moves in a straight line ....... in the . rear axle no differential movement of the…

A:

Q: triple beam balance?

A: Explanation given below.

Q: a. Carriage b. Tool post c. Compound rest d. Cross slide

A: Solution:

Q: QUESTION 2 Note: Work accurately to two decimal places.  Use a point (.) as your decimal place…

A: Given data: cylinder diameter d = 75 mm radius of crankshaft r = 70 mm length of connecting rod l =…

Q: 11. The twist drill is divided into .. main parts Select one: a.4 b.1 C.3 d.2

A: twist drill has three principles parts: the point, the body and the shank

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: Name the milling machine operation in which the dovetail grooves can be produced in the workpiece.…

A:

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot           -     3Countersink      -     6Knurl                  -…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: describes the angular positions in terms of crank angle position in reationship with the

A: Given data To describes the relationship between angular position of crank and position of piston.

Q: In a single cylinder reciprocating engine, the primary unbalanced force is maximum

A: In a single cylinder reciprocating engine, there is one primary and one secondary unbalanced force.

Q: In SRP the main function of crank shaft is to convert rotary motion to reciprocating motion. Select…

A: Correct Option: True.

Q: The impending motion is applied when the body is Select one: O a. Just stopped Ob. Stopped Oc. Just…

A:

Q: U-CHANNEL IRON BASE motor 0 MOTOR 3.7 kW 3600 RPM +1.78 +1.32 +2.92 140 pump 0 89 +0.13 +0.97) +1.22…

A:

Q: How can angular displacement be determined by angular acceleration?

A:

Q: Which set of ordered processes best describes the steps to perform an emergency stop and reset of…

A: A lathe machine is used for the turning, facing, drilling, and surface finishing processes of…

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: What kind of endmill has many smaller teeth meant to distribute the load to reduce vibration during…

A: Select the endmill as below features: Utilize a bigger endmill with a bigger center measurement.…

Q: To take an angular measurement with an accuracy of 5 minutes you can use: Select one: O a. Vernier…

A:

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: The rim offset is the vertical distance between the rim centerline and the    of the disc.

A:

Q: What are the strokes of a four‑stroke cycle?

A: Inlet stroke- during this process piston moves from TDC to BDC inhaling air fuel mixture into the…

Q: ___________mm4 is the polar moment of inertia of a hollow shaft if its external diameter is 150mm…

A: The polar moment of inertia is termed as an axis which is basically perpendicular to the plane of an…

Q: Identify the side relief angle (in degrees) from the following single point tool signature 1-…

A:

Q: If the moment of inertia increases, then what will happen to angular velocity?

A: Given Moment of inertia Angular velocity To find Relationship between moment of inertia and angular…

Q: The tool is shaper machine is fixed axis. O a. Z O b. A O c. Y O d. X

A:

Q: Gear wheels are produced by using grinding cutter.

A: This statement is (FALSE)

Q: List three benefits of holding a workpiece between centers

A: A work holding technique is to hold the objects between the centers. One of the centers is mounted…

Q: In directional drilling where the wellbore finished dropping inclination is called…

A:

Q: perpendicular to the plane of the gear The side surface above the pitch cirnd de surface above thee…

A: Option d is correct.

Q: The rolls are supported on bearings of side frames called *

A: The rolls are supported on bearings of side frames called Answer: Supports

Q: What is the value of the dimension measured on the following Vernier Caliper in mm? cm 6i234 5š67 8…

A: The vernier calliper is used to determine the interior and outside dimensions of steel items.…

Q: Drill bit is fixed in the headstock of a lathe during the drilling operation. Select one: True False

A: Drill bit is fixed in the chuck and the chuck is attached to the headstock of the lathe.

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.