The angle bracket shown, 75 mm x 75 mm x 15 mm thick, is 200 mm long. It is connected to the 16 mm thick flange of the column support with 2 of 16 mm diameter bolts. The bracket is subjected to a load of 42 kN from beam A. Assume that the load is applied concentrically at the  connection.   1. Determine the resulting bolt shear stress in MPa 2. Determine the resulting bolt shear stress in MPa 3. Determine the critical bolt shearing stress in MPa

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A: To Determine Largest allowable gauge pressure, P

Q: Determine the maximum resultant stress on the 20mm fillet weld. L1 = 200mm, L2 = 250mm & L3 =…

A: Answer:

Q: What is the shear stress in the 25-mm diameter bolt at pin C if P = 25 KN? A 50.93 MPa B 67.91 MPa…

A: Given,  dc = 25 mm  P = 25 kN

Q: A welded bracket connection shown below carries a load P. If the thickness of the weld is 8 mm. If P…

A: Thickness of Weld = 8 mm P= 180 KN A welded bracket connection is a type of joint in which a bracket…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A:

Q: A connection using 3 bolts with the eccentricity is shown in Figure Q3. Determine: (a) Average shear…

A:

Q: An eccentrically loaded bolted connection is shown. Diameter of A 325 bolts in standard holes is…

A:

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P= 50…

A:

Q: The five-bolt connection shown must support an applied load of P = 374 kN. If the average shear…

A: Given data in question  Load = 374 kN Shear stress= 321 MPa 5 bolts To find out  Minimum diameter of…

Q: Calculate the maximum shearing stress developed in the 5 – 16mm diameter bolts 100 mm 100 mm P=…

A:

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

A:

Q: 7. An angle ISA 150 x 75 x 10 mm thick, steel tension member is connected by its long leg to a 10 mm…

A:

Q: 4. A flanged bolt coupling consists of eight steel 20-mm vois spdceu evenly around a bolt circle…

A: Given no of bolts =8 Diameter of bolts =20 To fit evenly in circle of 300 mm diameter Sharing…

Q: 10/10 find the tensile stress in upper plate in section 3-3 2 1 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN…

A:

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

A:

Q: For the connection shown, the average shear stress in the 8-mm-diameter bolts must be limited to 158…

A:

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: For the connection shown, determine : a) Sigma (stress) on the plate, if N = -6 kN (negative sign…

A: Given:- Thickness of plate, t = 10 mm Width of plate, w = 2R = 2 x 30 = 60 mm Diameter of pin, d =…

Q: 2) The angle member is connected to the W section member by 4-19 mm diameter bolts as shown in the…

A: Bolts in connection fails in  shearing and bearing. Shearing stress - Shear stress is generated when…

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: he five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

A:

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

A:

Q: The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear…

A: Given Load 371 kNStress 174 MPaNumber of bolts 5To find out Minimum diameter

Q: the allowable tensile load on the members and weldlength and overlap length of

A:

Q: A tension member with an allowable tensile stress of 0.6Fy is connected to the gus using four rivets…

A: According to given data  A tension member with an allowable tensile stress of 0.6Fy is connected to…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).