I need to draw a circuit but I couldn't figure out how. Can you help me please? The alarm circuit in a car is controlled by 5 switches. These are:B: driver,A: ignition switch,C: driver's belt,E: front passenger belt.D: front passenger andCSwitches are initially in the off state. Switch A opens in the ignitionDstate. When the person sits, the relevant key opens. If the belt isattached, the relevant key opens. Design the circuit that will alarmwhen the car is moving and any of the front seats are occupied and theA: MsDseat belt is not fastened.Follow the way given below:1- Draw the truth table.2- On truth table, show in which cases alarm will be on.3- a) Reduce the function ( by using third order MEV method and K-map) And write the logicalexpression.4- Draw the circuit.m m w w W

The alarm circuit in a car is controlled by 5 switches. These are: A: ignition switch, C: driver's belt, E: front passenger belt. B: driver, D: front passenger and C Switches are initially in the off state. Switch A opens in the ignition D state. When the person sits, the relevant key opens. If the belt is E attached, the relevant key opens. Design the circuit that will alarm when the car is moving and any of the front seats are occupied and the A: MsD seat belt is not fastened. Follow the way given below: 1- Draw the truth table. 2- On truth table, show in which cases alarm will be on. 3- a) Reduce the function ( by using third order MEV method and K-map) And write the logical expression. 4- Draw the circuit. w w w w m

The alarm circuit in a car is controlled by 5 switches. These are: A: ignition switch, C: driver's belt, E: front passenger belt. B: driver, D: front passenger and C Switches are initially in the off state. Switch A opens in the ignition D state. When the person sits, the relevant key opens. If the belt is E attached, the relevant key opens. Design the circuit that will alarm when the car is moving and any of the front seats are occupied and the A: MsD seat belt is not fastened. Follow the way given below: 1- Draw the truth table. 2- On truth table, show in which cases alarm will be on. 3- a) Reduce the function ( by using third order MEV method and K-map) And write the logical expression. 4- Draw the circuit. w w w w m

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter9: Timing Relays

Section: Chapter Questions

Problem 6SQ

See similar textbooks

Similar questions

What is the name of the device shown below? CE O a. DC regulated powersunpy: Ob.C.R.O Oc. Control Panel Od.Function Generator
Explain by drawing how intermediate switch is working in ON and OFF position.
In order to control the opening activation of a safe, a contactor Z is used that controls the respective electronic key, and its activation is due to the combined action of three mechanical switching devices "Switches" A,B, C. To activate the electronic key, the switches must meet the following conditions. 1.Switch B must be inactive, and the corresponding switches A and C active. 2.Switches B and C active and switch A inactive. 3.Switch A active and the corresponding switches B and C inactive. Finally, switch C active and the others inactive. Truth Table. Functional circuit with multiplexers.
Write a ladder program for a system with the following control: 1. A blue lamp is ON if switch A is ON and it not be OFF even if switch A is OFF, it will be OFF if the switch B is ON. 2. Yellow lamp is ON for 5 minutes by switch C. 3. Red lamp is going to be ON/OFF by switch D, This process is worked if and only if the yellow lamp is ON.
Explain a DPDT switch with a drawing and how they work. Also explain NC and NO on the drawing. Please answer in typing format please ASAP for the like Please it's urgent
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B
Write the applications 5-5 each of toggle, push, limit, rotary, DIP, selector switch.
Circuit breaker has minimum contact gap between fixed and moving contacts during arcing. O a. SF6 O b. oil O c. air blast O d. Vacuum
A motor device is labeled 150 mFd. This device is a A. centrifugal switch.B. stator.C. capacitor. D. rotor.
12.a. A maintained push button willA. hold its position after it is pressed and released.B. open after it is released.C. open after a power failure.D. close after it is released.12.b. Sensors that detect the presence or absence of reflected light areA. inductive proximity.B. capacitive proximity.C. fiber optic.D. photoelectric.
DO NOT WRITE THE CODE IN HANDWRITTEN Write an Arduino code to control two LEDs using two push buttons, given the bellow setup: LED 1 is connected to pin 2 LED 2 is connected to pin 12 Button 1 is connected to pin 11 Button 2 is connected to pin 10 If both push buttons are pressed, LED 1 is OFF and LED 2 is ON. If one of the push buttons is pressed LED 2 is OFF and LED 1 is ON. hint: you may use the if..else if statement (note: you may use other approaches)
A starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct?