The advantage of using an open mold is which one of the following: O higher production rates are possible smoother surfaces are achieved on both sides of the molding O the interior of the mold is accessible O the mold costs much less than if two matching molds were used

The advantage of using an open mold is which one of the following: O higher production rates are possible smoother surfaces are achieved on both sides of the molding O the interior of the mold is accessible O the mold costs much less than if two matching molds were used

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For casting the part, whose perspective pictures are given below, into sand mold,model design, core design if necessary, all molding stages andFinally, draw the mold in the most suitable form for casting and shape all the mold elements.Name it by showing on it (Note: The hole shown in the figure is a full hole.) !!! Please draw the desired shapes !!
For the casting of the part whose perspective pictures are given below, take into account the section surface (model design), (core design if necessary), all molding stages and finally (the mold in the most suitable form for casting) and name all mold elements by showing them on the figure (Note: The hole seen in the figure is a full hole.)
I need the answer as soon as possible
For the sand casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and and finally draw the most suitable form mold for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
Aspiration effect filling and uniform ramming of sand in molds, O spiral mold test The action of raising and dropping (lowering) air is sucked in or entrapped in the liquid pressure is applied by a pneumatically operated piston allow escape of gases during pouring Jolting
For the sand casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and and finally draw the most suitable form mold for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.) please draw the shapes more clearly and remember to draw each step.Thank you in advance
QUESTIONS 1- Describe with net sketch: a. Pattern b. Riser c. Runners d. Core 2- Compare between open mold and closed mold. 3-Explain the main Procedures of Sand Casting. 4 - What are the important properties which are essential in good molding sand? Explain in details. 5- Mention advantages and disadvantages of casting. 6- Describe types of sand mold. 7- What are the common binders of sand mold and cores? 8- Describe Desirable Mold Properties. 9- Explain two types of patterns and two pattern allowances 10- Describe with sketches shell process casting (i) Composition of sand mixture (ii) Steps in molding (iii) Advantages (iv) Limitations and (v) Applications 11- Explain with Sketch the construction and operation of a hot chamber die casting machine. 12- Compare between hot chamber die casting and hot chamber die casting. 13- What is meant of investment casting? What are the main materials used for making the investment pattern. 14- Describe various kinds of patterns in use. 15- Why…
QUESTION 1 a) Explain what is the basic difference between expendable and permanent molds used in metal casting? Briefly also describe what are the primary advantage and disadvantage of each these two types of molds? (CO1, PO1, C2) b) Describe the steps involved in making the sand mold and the casting, including what steps that may be needed to improve the casting after it is hardened and removed? (C01, PO1, C2) c) One of Open Mold processes for shaping fibre reinforced plastics (FRP) is Hand Lay Up. List the five (5) steps involved in the Hand Lay Up method? (CO2, PO1, C2`
What are some of the operations required of sand castings after removal from the mold
no hurry ............. a very good handwriting with every step to be mentioned to understand the answer easily step to follow given requirement solution result if not followed the above steps , ready for consequences i want the solution with a very good handwriting
For the casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure (Note: The hole shown in the figure is a full hole. .)
speed