The A/D converter is used for the digital transmission of an analog signal the digital transmission of a digital signal all of the preceding None of the given answers A Moving to another question will save this response.

Q: The time constant is the time required to Select one: a. Reach 63% of the final value O b. to reach…

A:

Q: convert 128 from Hex to Octal converter

A: First we will convert Given hexa decimal number into decimal number and than we will convert decimal…

Q: Question 4 The A/D converter is used for the digital transmission of an analog signal the digital…

A: Input to the A/D converter is Anolog signal and output is digital signal.

Q: The series circuit is an energy converter . into what type of energy is the electrical energy…

A: Given: Series circuit converter

Q: 1. Positive clipper with positive bias 2. Positive clipper with negative bias 3. Positive clamper…

A: Positive clipper with positive bias : A Clipper circuit in which the diode is attached in series to…

Q: Δν What is the time constant of the circuit in the figure? A) RC/16 B) RC/8 C) 8 RC

A:

Q: loop operation is followed in SMPS operation.

A: Open loop

Q: In this image what is t and it indicates the time for what ?

A: Heisenberg's Uncertainty Principle is the following:∆E.∆t>hwhere delta(E) and delta(t) are the…

Q: The merging of a free electron and hole is called recombination bonding charge balancing none of…

A:

Q: Which one of the following is the correct implementation of this multiplexer?

A:

Q: Choose three (3) correct characteristics of the following counter circuit. HIGH HIGH FF0 FFI CLK…

A:

Q: if the Johnson counter start with sequence 1010 what is the output after three clock pulses 1100…

A: The given input sequence is 1010. The johnson counter is a shift register with its input data as the…

Q: Please answer in typing format

A: Step 1:Given circuit is,                  The input voltage Vi is in the range of -10V to +10V. The…

Q: The number of Hamilton Circuits in K20 is

A: Hamilton Circuits:A Hamilton circuit is one that passes through each point exactly once cover all…

Q: The phase modulated carrier has a constant amplitude a constant angle a constant phase none of the…

A: Phase modulation is one of the angle modulation technique.   Angle modulation technique is…

Q: The A/D converter is used for the digital transmission of an analog signal the digital transmission…

A: In this question we will write about A/D converter...

Q: The time constant of an LR circuit represents the time in which the current in the circuit A Reaches…

A: Given circuit is a LR circuit, For LR circuit current is given by, I=Io1-e-tτ.

Q: Which of the following is true about acceptable Percent Errors?

A: The solution is given below

Q: D 00000 R 1Q Q

A: As we can see the clock is provided to the first flip flop only and clock of otger flip flops are…

Q: What will be the value of R1 with the given RTL code XOR , where R1 is 1011 0110, R2 is 1100 0111

A: Given that in RTL code R1 is stored as R1 = 1011 0110 and R2 = 1100 0111 And the operation is XOR…

Q: Question Bulding with Full adder using Magnitude Comparator

A:

Q: the difference between the following two hexadecimal numbers: 712 and 400 is given in the…

A:

Q: Find the relative static error when the true value of a resistor is 100 Q, while its measured value…

A: Given, True value of resistor, Rt=100 Ω Measured value of resistor, Rm=105 Ω

Q: QUESTION 5 Analog output modules are used to simply set an output either on or off O True False

A: Given, Statement is  A statement about the output of the analog signal is given. To find out We need…

Q: A signal is passed through a LPF with cut-off frequency 10 kHz. The minimum sampling frequency is…

A: if Fm is the maximum frequency in the signal , then minimum sampling frequency is 2Fm  .  and cutoff…

Q: turn off time is the time

A:

Q: For energy signals , the energy will be finite and energy power will be O finite can not be defined…

A: A signal is energy if total energy has non zero finite value. A signal is power if total power has…

Q: Given the following figure, select from the options below the waveform that shows correctly the…

A: The digital circuits can be sequential or combinational circuits. The combinational circuits depend…

Q: What will be the value of R1 with the given  RTL code XOR , where R1 is 1011 0110, R2 is 1100 0111

A: Given, R1 = 1011 0110, R2 = 1100 0111 RTL code XOR =?

Q: Draw the Vs and is as a function of time when the switch on at t=0 R3 S2 ↑ Vs Rr=0⁰ Ro E к

A: As it is purely resistive Circuit and it is opened at the end then no current will flow and there…

Q: A multiplexor is a combinational circuit that passes multiple data inputs to multiple data outputs O…

A: We need to determine the number of inputs and outputs in a multiplexer.

Q: Question 10 The A/D converter is used for the digital transmission of an analog signal the digital…

A: A/D converter means analog to digital converter.

Q: Obtain the Thevenin equivalent of the circuit in Fig. 4.36. Practice Problem 4.10 Answer: VTh = 0 V,…

A:

Q: Implement a full adder with 2 4x1 multiplexer

A:

Q: The desired hexadecimal values are in octal format.

A:

Q: Time taken for the response to raise from * 10 to 100 % is Setting time O Peak time O Delay time O…

A: Time taken for the response to raise from 10 to 100 % is  A. Setting time  B. Peak time  C. Delay…