Answered: The 8085 programming manual says that…

The 8085 programming manual says that it takes seven T States to fetch and execute the MOV instruction. If the system clock has a frequency of 2.5 MHz, how long is an instruction cycle ?

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 3SAT: The time it takes to perform the fetch instruction and decode instruction steps is called the...

See similar textbooks

Related questions

Q: determine the time taken to execute the instruction if the clock frequency of 8085 is 10MHz. Mvi…

A: In 1977, Intel designed an 8- bit microprocessor by using NM technology, which is called 8085…

Q: Why would the current instruction be reset if a problem occurred?

A: Malfunction cause : When a user requests that the CPU access a particular memory page, the CPU…

Q: If an instruction is not accepted and it writes to VA page 30, what will happen? A TLB that is…

A: Given: Instructions that write to VA page 30The Translation Lookaside Buffer (TLB) table is searched…

Q: This R format instruction adds the four bytes that the source register holds and puts the sum into…

Q: An NOTX instruction's size would be: 1 byte 2 bytes 3 bytes 0 byte choose the right

A: Actually, 1 byte =8 bits.

Q: Another name for step 2 of the instruction cycle is ? Fetch search operate decode

A: Fetch, decode , read and execute are the 4 steps of instruction cycle.

Q: The execution cycle of an instruction can be described using Register Transfer Notation by writing…

A: Intro The instruction execution cycle comprises the following steps: Fetch Decode Execute Store The…

Q: SBB instruction is arithmetic in type.

A: True Sbb-arithmetic instruction-microprocessor, Assembly Language SBB: Subtract with Borrow…

Q: The FADD instruction accepts a variety of operands.

A: The following is a list of the operands that may be used with the FADD command.

Q: What would happen if an instruction was disobeyed, and why would that be the case? In the following…

A: Given: When an instruction is written to page 30, it comprises the following information: If the…

Q: What would cause the current instruction to be reset if there was a problem?

A: Introduction: A page fault is a term used to describe memory pages, and when a user requests that…

Q: Execute the following instruction using zero address instruction. X=X*Y+Z/A-B*C+E*F *

A: The execution of the following Instruction using zero address instruction X=X*Y+Z/A-B*C+E*F is…

Q: it t

A: A microprocessor is a computer that executes user instructions. Instructions must be written in a…

Q: We can start executing an instruction even before the end of the Fetch cycle Select one: O True O…

A: Instruction Cycle : Every instruction has a set of operations for its complete execution. This…

Q: If the clock rate of a TMS320C64xx DSP is 600 MHz, how many instructions can it provide to the CPU…

A: It is given that :- The number of bits in an instruction of a TMS320C62xx digital signal processor,…

Q: The Fetch step of the instruction cycle loads the instruction stored at the program counter and puts…

A: In the field of computer architecture and central processing units (CPUs), the instruction cycle is…

Q: What is the time delay when implementing the NOP instruction which takes 4 T-states of processor…

A: Find the required answer with calculation given as below :

Q: ASSEMBLY The ROR instruction is only suitable for signed integers. True False

A: Given: ASSEMBLY The ROR instruction is only suitable for signed integers. True False

Q: Given clock = 10MHZ, what is instruction cycle? Please show how to generate 1 second delay. (You can…

Q: In a SRL instruction, if we perform shift on a number by two positions, the number is divided by 2.…

A: SRL instruction stands for Shift Right Logical.

Q: A one-byte instruction has Oopcode and an operand O opcode only Oopcode and two operand Ooperand…

A: A one-byte instruction has opcode and an operand.

Q: Do you know what would happen if an instruction was rejected? TLBs controlled by software are…

A: Instructions that write to VA page 30The Translation Lookaside Buffer (TLB) table is searched for…

Q: In a SRL instruction, if we perform shift on a number by two positions, the number is divided by 4.…

A: SRL instruction shifts a register value right by the shift amount and places the value in the…

Q: Amdahl’s Law I found that I can replace one of my instructions that takes 111 ns, with a different…

A: Amdahl's Law is a fundamental concept in computer science and performance optimization. It addresses…

Q: Decode the instruction is the third phase in Fetch-Execute Cycle. 1 - True 2- False

A: The basic operation of a computer is called the ‘fetch-execute’ cycle. The CPU is designed to…

Q: How many clock cycles does the ADD E instruction take to run? Write it down in Register Transfer…

A: Dear Student, The answer to your question is given below -

Q: Both the source and the destination are left unchanged when using a CMP instruction. Decide on one…

A: The answer :

Q: Execution of instruction is controlled by memory unit 1-true 2-false

A: EXPLANATION: The Memory Unit is also referred to as the Storage unit, main memory, RAM. The…

Question

The 8085 programming manual says that it takes seven T States to fetch and execute the MOV instruction. If the system clock has a frequency of 2.5 MHz, how long is an instruction cycle ?

Process by which instructions are given to a computer, software program, or application using code.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
The 8085 programming manual says that it takes seven T States to fetch and execute the MOV instruction. If the system clock has a frequency of 2.5 MHz, hiw long is an instruction cycle ?
determine the time taken to execute the instruction if the clock frequency of 8085 is 10MHz. Mvi a,32H LDA 2072H IN 40H Out 50h Lxi h,1234H
A MOV instruction asks for two operands: source and destination.
Amdahl’s Law I found that I can replace one of my instructions that takes 111 ns, with a different one that takes 57 ns. My program runs this instruction 50% of the time. What is the the speedup on the entire program by using this instruction?
How many clock cycles does the ADD E instruction take to run? Write it down in Register Transfer Notation.
Explain the fetch cycle in terms of the basic instruction cycle.
The clock cycle time of a pipelined CPU is lower than that of a non-pipelined one, but what exactly is the difference?
Another name for step 2 of the instruction cycle is ? Fetch search operate decode
What would occur if an instruction were to be disregarded? A software-managed TLB is quicker than a hardware-managed TLB in the following situations:
In a pipelined and non-pipelined CPU, what is the clock cycle time?