The 8 m long cantilever beam shown in the figure below carries a uniformly distributed load of 10 kN/m over a span of 2 m, a uniformly varying load that varies linearly from zero to 20 kN/m over a span of 5 m, and a 15 kN concentrated load at the free end as shown. Nearly sketch the shear force and bending moment diagrams What is the maximum shear force and where does it occur? What is the maximum bending moment and where does it occur? Find any points of contraflexure.

Q: The following figure shows a beam that is simply supported at Point A and Poi Load of (10 + P1) kN…

A: Calculate for SFd and BMD

Q: Figure 1 below shows a cantilever beam subjected to an axial compressive load of 450 kN acting at…

A: Given:-        Width  B=150 mmDepth D=300 mm1.1  Direct compressive stress=PA=450×103300×150=10…

Q: For the beam loaded as shown, determine the maximum shearing force and bending moment developed.…

A:

Q: Calculate the bending moment at points A and B for the beam shown below. 5 kN 2.5 kN/m A 1.5 m 4 m

A: Given beam:-

Q: For each of the loaded beams/cantilevers that shown in Figures 2 draw to suitable scale the normal…

A: A cantilever beam with point load, horizontal load, and uniformly distributed load near the support.…

Q: Find the bending moment and shear force diagrams for the following beam. What is the location and…

A: Shear force at A= Reaction at A=13kNShear force to the right of A = 13KNShear foece to the left of B…

Q: The arched beam in the following figure carres the concentrated vertical forces shown. Determine for…

A: As given in the question ,about the arch beam For calculation of support reaction , Equilibrium…

Q: Draw the bending and shear force diagrams of the beam whose cross section is given in the figure.…

A:

Q: The Figure below shows a cantilever beam subjected to a uniformly distributed load of Q=5.8 kN/m,…

A: Given a cantilever beam, it is required to plot shear force diagram, bending moment diagram and free…

Q: The radius of semi-circle R

A:

Q: igure Q2a shows a truss structure in static equilibrium supported at points A and B, where each…

A: F1=458KN,  F2=636kN, F3=870kN

Q: tion shown. Determine the maximum umber) and compression (a negative esses produced in segment BCof…

A: IN Section BC :Bending moment is M=17(1.1)=18.7kN-m

Q: QUESTION 1. Longitudinal and cross-sectional views of a beam are given in the figure below. (a) Draw…

A:

Q: The beam shown in figure below supports uniformly distributed dead and live loads. Based on the…

A: Given, Compressive strength of concrete f'c=25 MPayield strength of steel fy=420 MPaTake width of…

Q: A gusset plate for a bridge truss is shown in the figure. Determine the magnitude and direction of…

A:

Q: Theory of Bending and Deflection 12 in, 12 in 27 in 6 in. The following diagram will be used as a…

A:

Q: 1.1 A beam ABC 12 m long is simply supported at A and B where AB = 8 m. Point loads of 15 kN and 6…

A:

Q: The continuous beam shown below, is fixed at node 1, has a roller at node 3 and is hinged at node 2.…

A: Given data: Internal hinge at 2. Moment at 1 = -10 kN.m

Q: A 20 m long beam has two supports, A and B. The beam is pinned at Support A and supported by a…

A: Length of the beam(L)=20 m, Load on the beam(W)=18 kN Location of the load on the beam is 10 m.

Q: 1. In the figure shown, is a vehicle having wheel loads of P; and P, at a distance of 1.8 m.…

A: Given: Two wheel loads 72 kN and 59 kN at a distance of 1.8 m are acting on a bridge having 15 m…

Q: 1.1 A beam ABC 12 m long is simply supported at A and B where AB = 8 m. Point loads of 15 kN and 6…

A: Solution-