The 7442 is an integrated circuit BCD to Decimal decoder Note that on this device the inputs are A B C and D where A is the least significant bit 7442 INPUTS OUTPUTS vcc 16 15 14 13 12 11 ddddgodo 3 OUTPUTS Logic diagram of 7442 BCD-TO-Decimal decoder DISCUSSION: 1) What dose a BCD mean? 2) What are the bubbles on the 7442 logic diagram? GND 3) If a binary digit 1101 is applied as an input to 7442, what would the output be? 4)Show the decoding logic for each of the following codes if an active HIGH. 1000, 11100,101010, 000101, 0101

The 7442 is an integrated circuit BCD to Decimal decoder Note that on this device the inputs are A B C and D where A is the least significant bit 7442 INPUTS OUTPUTS vcc 16 15 14 13 12 11 ddddgodo 3 OUTPUTS Logic diagram of 7442 BCD-TO-Decimal decoder DISCUSSION: 1) What dose a BCD mean? 2) What are the bubbles on the 7442 logic diagram? GND 3) If a binary digit 1101 is applied as an input to 7442, what would the output be? 4)Show the decoding logic for each of the following codes if an active HIGH. 1000, 11100,101010, 000101, 0101

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit. The tpcg = 0.5 ns, tccq = 0.25 ns, tpd = 4 ns, tcd = 2.5 ns, tsetup = 0.5 ns and thold = 0.2 ns. What is the maximum value of fc? Select one: a. 0.2 ps O b. 200 MHz O c. 2 GHz O d. 200 KHz
What will be the boolean function (y) for the given CMOS logic circuit as shown in the figure? AMP, MP₂-B MP3 A—IL MN, BCMN₂ D- V₂ HCMN₂ DD MP -D MP-E y MN3C GND MNE
Questions 2) Design an exclusive OR gate using a 2-to-1 MUX and an inverter.
A d. B Figure 1 3. Referring to the logic circuit in Figure 1, determine: a. The simplified Boolean expression. b. The output waveform. C H c. Due to fabrication errors, lines d and f were shorted to the supply voltage. What happens to the output of the circuit? d. Your hardware resources are limited to 2-input NOR gate only. Draw the gate schematic of the simplified Boolean expression in 3(a).
Design a " 2 to 4" Decoder with SEL' (active lo) 1. Generate the logic gates and the equations 2. Draw the timing waveforms for all inputs/SEL and output. 3. Create an application that could use this simple Decoder
3a) Show the truth table for JK flipflop for positive edge clock triggering. 3b) if for time period T=1ms, level triggering clock signal changes as 10111 then show the output for the input, D=01001(Use D flipflop)3c) Make a 6-bit serial register.
i need the answer quickly
is there a way for the output voltage of a comparator to be the same as its supply voltage? im planning to connect its output to the input pin of a logic gate with the same supply voltage.
If a two-input logic gate produces a output of logic HIGH, only if both inputs are different, then the logic gate is O a. IC 7408 O b. IC 7486 O . IC 7432 O d. IC 7400
B) Draw the logic circuit for each of the following: 1) The operation 10110110 10101001
3d. will give thumbs up