The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T, and T, of V-belt just before it start rotating. B Ø- 120 mm 120 mm

The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T, and T, of V-belt just before it start rotating. B Ø- 120 mm 120 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

[3]. Two weightless slender rods are connected at Cby pin and attached to the blocks A and B of mass 10 kg, respectively as shown in Figure 3. The coefficient of static friction between the block A and horizontal plane is 0.25 while between block Band incline plane is 0.75. Determine the maximum values of P for which equilibrium is maintained. P 30° 60° 309 Figure 3: two blocks connected by slender rods
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless when mass m2 moves a distance 4.94 m up the ramp, how far downward does mass m1 move? d= ?
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
The coefficient of friction between the cylinder and the brake is 0.3. If the force P applied the brake is 20 N and the length d = 1.0 m, and a brake BC is to be arranged so that the speed of the cylinder may be reduced from 60 rpm to zero in 4 sec. Figure A is a solid cylinder weighing 600 N with a diameter of 0.60m. Find the total length L of BC. In m, 1 metric ton = 1,000kg = 9806.65 N Thirt ܕܗܘ] B d = 1. Om A a L-1 m mm
A brake test is carried out with a balance and a direct current motor. The purpose of this experiment is to calculate the torque on the motor shaft. The following values were obtained in the experiment. U=220 volts., I=107 amps, n = 1200 rpm. The length from the axis of the motor shaft to the point where the brake lever presses on the scale is L=80 cm. and the weight read on the balance G = 20 Kg. is Accordingly, calculate the following values: a) the shaft power taken from the shaft of the motor, b) the electrical power drawn by the motor from the mains c) motor total losses and motor efficiency Calculate
The Figure Q2 shows a ball and block with masses M1=10kg and M2, respectively. The block and ball are connected with a cable and pulley system. The coefficient of static friction for all contacting surface is 0.3. i) Determine the range of the mass of block so that the system is in M1 = 10 Kg equilibrium. ii) Determine the tension in the cable. M2 Hs= 0.3 Comment on your answer at question 2(i). 75%
The car shown in the figure below has a mass of 1673 kg. The coefficient of static friction between the rubber tires and the pavement is 0.6. Determine the maximum incline e [degrees] that the car can drive up if it has rear-wheel drive. 0.85 m (1.2 m 1.7 m
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.