The 500-lb beam is supported at A and B when it is subjected to a force of P = 900 lb as shown. (Figure 1) If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be neglected. Express your answer to three significant figures and include the appropriate units. μA ?

The 500-lb beam is supported at A and B when it is subjected to a force of P = 900 lb as shown. (Figure 1) If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be neglected. Express your answer to three significant figures and include the appropriate units. μA ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

The 490-lb beam is supported at A and B when it is subjected to a force of P= 1000 lb as shown. (Eigure 1) Figure B. 8 ft +2 ft
The 520-lb beam is supported at A and B when it is subjected to a force of P = 1000 lb as shown. (Figure 1) Figure 8 ft B < -2 ft- 1 of 1 Part A If the pin support at A suddenly fails, determine the beam's initial angular acceleration. For the calculation, assume that the beam is a slender rod so that its thickness can be neglected. Express your answer to three significant figures and include the appropriate units. α= Submit Part B μA By = Value Request Answer Determine the force of the roller support on the beam. Express your answer to three significant figures and include the appropriate units. μÁ Value Units Submit Request Answer ? Units ?
The rope shown in the figure below is wound around a cylinder of mass 4.0 kg and I = 0.020 kg m2, about the cylinder axis. If the cylinder rolls without slipping, what is the linear acceleration of its center of mass? What is the frictional force? Use an axis along the cylinder axis for your computation. What happens if the frictional force between table and cylinder is negligible? Choose any axis for your computation.
3. Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass of 50 g. If 0 is 15° and the angular acceleration is 20 rad/s? M 3 m W Figure 3
D Icd A lab CC BY UBC Engineering Three (3) arms CD, BC, and AB are pinned to form the mechanism shown. Link AB has a length of lAB = 0.5 m, link CD has a length of lcD 0.5 m, and the distance from B to C is rc = B – 1î + 1j m. If the angle between link AB and the horizontal is 0 = 45°, determine the angular acceleration of link CD. The rad 个 angular velocities of the links are given as WAB = - 2.5 k rad and wBC = 1.25 S while 2 S the angular acceleration of AB is given as rad - 4.5 k A AB 82 d k ra- aCD
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. A Ja B C P Determine the corresponding angular acceleration of the rod. The corresponding angular acceleration of the rod is rad/s² O.
The figure shows the rear rotating axle of a 4-wheel wagon with the same FRONT AXLE design and REAR AXLE design. The wagon moves at a constant speed and the diameter of the wheels carrying the axle is D=512 mm and the circumferential speed=3.1 m/s. Due to the load (m) on the wagon, a force of 16574 Newtons acts in the vertical direction. ALSO, a horizontal force of 21% of the vertical load acts on the wagon laterally (horizontally) in bends. It is planned that the bearings of the axle will be bearing 6008 deep groove ball bearings. Calculate the life of bearing A in hours.The radial effect of lateral loads will not be taken into account in the bearing force calculation. Fo.Fa/Co = 1.38 Pi=3.14
Turning moment 1mm = 60NM: crank angle, 1 mm = 1°. The turning moment shows the maximum energy that needs to be stored by the flywheel in unit area is 2850 m?. The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m3. Reply.
QUESTION: It is wanted to withdraw from A end with V_A velocity velocity (a_A = 0 m / s ^ 2) as shown on AB rod. Find the force F that will satisfy this condition. In this case, what are the support reactions at A and B points? Ignore the mass and atalat moments (I) and friction forces of the wheels. The inertia moment table of the rod is given.
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180 , and ? = 180? and ? = 360? respectively. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed.