The 50 N force is applied to the lever cutter handle. Determine the force exerted by the cutting blade in part E. Dimensions in mm. Explain the strategy used to solve the prob

Q: please solve the  equations in steps ()i and ()ii

A:

Q: 15 ft – 15 ft 15 ft 5 kips 5 kips 9 kips |A J 8 ft K F I Bo E H.

A: Vertical force applied at pont D on the truss = 5kips Vertical force applied at pont G on the truss…

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: To findDraw the loading diagram showing the internal forces and moment/Torque acting on a cut…

Q: Steam in a piston-cylinder assembly undergoes a polytropic process, with n=2, from an initial state…

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: O AEd It vec B, = N Submit Request Answer Part E- Part E There exists a point of zero shear between…

A:

Q: The 2-1b spool slides along the smooth horizontal spiral rod, r = (20) ft, where is in radians, as…

A:

Q: u 30° 40° F = 600 N 22

A:

Q: The beam shown below is suspended from two steel rods as shown and is initially horizontal. The…

A: First let us find the forces acting on rod AD(FAD) and CE(FCE), Due to symmetry , FAD = Q/2 and FCE…

Q: Silicon is diffused at 1100°C for 20 minutes with bismuth (Bi). You measure a diffusion length of 1…

A: (d) Write the initial total amount of Bi. Biinitial=2×1015 atoms/cm2

Q: Consider the schematic of a riveted lap join subjected to tensile load F, as shown below. Le d be…

A: TO determine the minimum value for the thickness of the plates.

Q: Indicate the magnitude of the other Force components. Use values given. Angle of drawing may not be…

A: The magnitude of force is .The dimension is

Q: (a) Draw the FBD of A and B when the wedge B impends to slide to the left. Friction is negligible…

A:

Q: •3-25. Determine the maximum weight of the bucket that the wire system can support so that no single…

A:

Q: Find the ratio for the tool P and Q

A: Given data,  Two tools P and Q have signatures       50-50-60-60-80-300-0 and…

Q: The bar is made from welding two uniform 40 lb bars together. Calculate the magnitude of the pin…

A:

Q: Given the 600-N force applied to the bracket at A in Fig 1, determine:

A: Given Data: The force acting at point A is F = 600 N. The angle made by F with the east direction…

Q: Moment of the single 100 lb force i. When the tail of the force is at its original position using M…

A: Given, We have to consider only the single 100 lb force.

Q: Find the. Force

A: Given  The magnitude of Force F1= 1000 N                                        F2=880 N

Q: Determine the magnitude of the pin reactions at B and C if W = 2400 lb. %3D

A:

Q: The cylinder head of a piston-type air compressor is held in place by ten bolts. The total joi…

A:

Q: resultant force on the contracting gear tooth is

A: Given data; as shown in fig; for resultant force on contacting gear tooth; Torque;…

Q: The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces.…

A:

Q: 4,000 Ib 2,000lb A B C L000 Ib F--10- T-10"--- 10°-+--10"--►

A:

Q: Fn FRY F = F, cos o F.

A: Let R be the resultant force acting on contacting gear tooth, then R = √(Ft2 + F2R) R2 = Ft2 + FR2…

Q: The pin P slides in the disk slot and also in the spiral slot cut in the reference frame and defined…

A: Given: r=0.1 θ metersθ= 0.3 rad s˙ To find:

Q: 3-3. Knowing the forces in members A and C, determine the forces FB and FD acting on members B and D…

A: The given force system is concurrent at O.600 angle is changed to 300The force in FBD

Q: The moment of inertia of the pulley about its axis is I = 0.005 kg.m2. If the 5-kg mass A is…

A: