The 50 m distance between the booth A and booth B is measured by pacing three times with a result of; 102, 101 and 100. Another distance between booth B and booth C is paced with a result of; 255, 257,259. Determine the distance bet booth B and C. Group of answer choices a. 127.228 b. 127.528 c. 127.428 d. 127.328

The 50 m distance between the booth A and booth B is measured by pacing three times with a result of; 102, 101 and 100. Another distance between booth B and booth C is paced with a result of; 255, 257,259. Determine the distance bet booth B and C. Group of answer choices a. 127.228 b. 127.528 c. 127.428 d. 127.328

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam in Figure 3 is subject to a point load F. The length A is 0.75m, and the length B is 1.39m, The beam is rectangular having a cross-sectional width of 39mm, and a depth of 8mm, and a Young's modulus of 209GPA. Figure 3. F A B The point load is 52N The Factor of Safety for the component is 1.53. Determine the maximum shear force (Answer in N only). Determine the maximum bending moment (Answer in Nmm only). Determine the maximum axial stresson the top surface of the beam (MPa). Determine the maximum axial strain in the beam (strain). Determine the the minimum yield stress (MPa) based on the FOS.
i li. :: M P \:£9 ملاك الروح قبل دقيقة واحدة If the single random error + 17.9 mm, the total :random error in 6 measurements is II
Q1). The following consecutive readings were taken along a straight line from station (11+090) to station (12+015). The instrument has been changed after third, (3 fifth, eighth and welfth readings. The readings are as bellows: 0.68 D. 0.680, 1.455, 1.855, 2.330, 2.885, 3.380, 1.055, 1.680, 2.265, 3.540, 0.835, 0.945, 1.530 and 2.250, first and last point are a bench marks having elevations 50.25m and 50.81 m respectively. 44.8 1- Draw page of level book and enter the above data. 2- Find elevation of points by height of instrument method. 3- Check your calculation. 4- Determine the gradient of the line joining the first and last point. 5- Determine loop closure and adjust calculated elevations. -5.408
Q1). The following consecutive readings were taken along a straight line from station (11+090) to station (12+015). The instrument has been changed after third, B fifth, eighth and welfth readings. The readings are as bellows: D 0.6 0.680, 1.455, 1.855, 2.330, 2.885, 3.380, 1.055, 1.680, 2.265, 3.540, 0.835, 0.945, 1.530 and 2.250, first and last point are a bench marks having elevations 50.25m and 50.81 m respectively. 44.8 1- Draw page of level book and enter the above data. 2- Find elevation of points by height of instrument method. 3-Check your calculation. 4- Determine the gradient of the line joining the first and last point. Vs 5- Determine loop closure and adjust calculated elevations. -5.408
fast please!
Q1). The following consecutive readings were taken along a straight line from station (11+090) to station (12+015). The instrument has been changed after third, fifth, eighth and welfth readings. The readings are as bellows: B D 0.680, 1.455, 1.855, 2.330, 2.885, 3.380, 1.055, 1.680, 2.265, 3.540, 0.835, 0.945, 1.530 and 2.250, first and last point are a bench marks having elevations 50.25m and 50.81 m respectively. 44.8 1- Draw page of level book and enter the above data. 2- Find elevation of points by height of instrument method. 3- Check your calculation. 4- Determine the gradient of the line joining the first and last point. 5- Determine loop closure and adjust calculated elevations. -5.408
Please answer with solution.
The accompanying schematic arrangement of line portray a differential level route. Th values indicated represent back-sight and foresight readings taken at different points as labelled. Prepare the complete differential level notes for the information shown and the customary arithmetic check. STA. BS HI FS ELEV. BM1 2.35 356.65 TP1 1.37 3.28 TP2 3.08 2.04 ТРЗ 1.54 3.61 ТР4 0.85 3.69 BM2 3.07 Arithmetic Check: Elevation BM1+(SUMMATION OF BS) -(SUMMATION OF FS) =BM2 A. Height of the instrument at TP4. B. Elevation of TP4. C. Difference in elevation of TP1 and TP4.
T1
Module 03- Coursework Activity 03 Complete the Differential Leveling Notes by providing data to the unknown quantities. STA FS BM1 TP1 TP2 BM2 BM3 TP3 BM4 BS 1.256 1.116 1.228 1.189 1.070 1.831 HI 1.886 1.527 2.246 2.017 2.656 2.765 ELEV 127.133
Q2) a.) Find the intersection coordinates of lines passing from AC and BD. b.) Find the area defined by the corner points A, B, C, and D. The Lengths in the below given figure are in meters. Use Gauss Method only. 17.42 B e----165.05 37.15 55.98 Yp Хр 39.47 22.75L D ol4.90 i 13.90 A 0.00 ty
Moment Area: Find theta B using moment area method (constant EI)