The 5-lb box slides on the surface for which uk = 0.3. The box has a velocity v = 15 ft /s when it is 2 ft from the plate. (Figure 1) %D %3D

Q: In a facility that processes consumer shipr certain packages are redirected by the trac pictured. A…

A:

Q: 3. The 75-kg chest shown is intended to be moved P= 400 N 15° 一十一 under the condition shown. Does…

A:

Q: Figure 2(a) shows a crate with a mass of 55 kg is projected down with an inclination angle 0. If the…

A: Given data: The mass of the crate is m=55 kg The initial speed of the crate is u=7 ms The…

Q: The 3,000lb race car is up and running again and slides into a wall at 150mph. What is the kinetic…

A:

Q: ml kg m2 kg Calculate the vertical acceleration a of the cylinder m1 in m/s?, where m1 = 122 kg and…

A:

Q: While the astronauts are trying to fix the crane, the cable slips off the pulley and the buggy falls…

A: Once applied, force is described as an external cause that alters or tends to modify the…

Q: What should the mass m (kg) be for the system given in the figure to remain at rest? There is…

A: Draw the free-body diagram for the above system.

Q: Blocks m = 4.0 kg and m2 = 1.0 kg are connected by a thin, light cord which is draped over a light…

A:

Q: increases to F, 80 lb once in the pool. What is the speed of the raft when s = 5 ft?

A:

Q: A bicycle and rider of mass 120 kg are travelling at a speed of 15 km/hr on a level road. The rider…

A:

Q: Put a marble with the mass m = 4.5g into a jar with honey. The drag force F exerted by the box is…

A: Given data mass of marble = 4.5 gram = 4.5 x 10-3 kg medium : honey

Q: With the radius of curvature (r) at the top of the loop (T) is 1 m. Determine the minimum speed (in…

A: Given data: mass = 0.1 kgradius of the loop =1 m

Q: Question 2 A rope of length L = 2.2 m and mass m = 5 kg is initially at rest and can slide on an…

A:

Q: 3. Find the distance the 50-kg crate has traveled and its velocity at t = 3 s. The coefficient of…

A:

Q: A small cart of mass m = 1.8 kg is running with a velocity of v = 2.5 m/s on a frictionless surface.…

A:

Q: The box has a mass of 50 kg and is at rest. When it is pulled with 1000 N it reaches speed of 5m/s.…

A: Given data: Initial velocity of the box, u = 0 m/s. Final velocity, v = 5 m/s. Mass of the box, m =…

Q: Given: - The original length (1) of the elastic cord is 2m. - Spring constant is 150 N/m. - 0= 25°…

A: Given that, Length of the cord, l=2 m,Spring constant, k=150 N/m,Angle θ=25°,Mass of the ball, m=6…

Q: A bicycle and rider is mass 125 kg are travelling at a speed of 10 km/hr. The rider applies a break…

A:

Q: 5. A muon has a mass if 1.88x10-28 kg and impacts the Earth's atmosphere. It slows its travel from a…

A: Dear Student you have posted two different questions but as per Q & A guidelines I will solve…

Q: The 65 g projectile travelling at vh 790 m/s strikes and become embedded in %3D the mB = 35 kg…

A:

Q: t is its acceleration? - same box in this problem above is pushed with the same n and applies a 2…

A: Information given⇒ Box mass(m)=100 kg Force applied to box(F)=25 N

Q: The crate of weight W=40 Ib has a velocity VA=12ft/s when it is at A. Determine its velocity(ft/s)…

A:

Q: A 100 pound pipe is at rest vertically, when the cable is connected to B at the force of P=50…

A:

Q: Q2/ Three blocks having masses of 5 kg , 10 kg and 15 kg are in contact on a fixed smooth inclined…

A:

Q: Q2/ The 150 box being pulled in 14 sec by the M winch M, If the winch efficiency is c= 0.65 and the…

A: Given :Mass of box,M=150Kg(unit assumed as not given)Power input,Pi=20KWEfficieny of…

Q: A force F (magnitude F) acts on a box of mass m resting on the ramp and the box remains at rest. The…

A: Determine the normal force on the block.

Q: AE-3-9 The 12-kg mass A in Fig. (a) slides with negligi ble friction in a semicircular trough of…

A: Given data: Draw the free-body diagram of the mass. The net force acting in the direction of “t”…

Q: final velocity of the block is to value.

A: Need to find final velocity of block.

Q: magine an imperfect bowling ball that is weighed to one side so that its center of mass is no longer…

A: If we consider the vertical component, we can determine how long the ball is in free fall. We can…

Q: A 2kg mass is initially traveling at a velocity of 0.95 m/sec. Kinetic friction coefficient between…

A: Given data, m = Mass of the body = 2 Kg u = Initial velocity of the mass = 0.95 m/s μk = Kinetic…

Q: What is its position and velocity at t= 9.2 s? What is the new velocity and new position?

A:

Q: Determine the driving force and normal force exerted by the partially spiral track on the 200- kg…

A: Find the driving force and normal force on the motorcycle.

Q: Determine the velocity of the weight A at this instant. The cord is 20 ft long. Express your answer…

A:

Q: A helicopter with a mass of 10,000 kg takes off straight up at t=0. The thrust of the engine is…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.