The 5 kg block A travels to the right at va = 0.61 "/sec at the instant shown in the figure. If thecoefficient of kinetic friction is f= 0.2 between the surface and A, determine the following:а.the velocity of block A when it has moved 1.2 m. Answer in m/sec.b. Acceleration of block A and B. Answer in m/sec?.c. Magnitude of the force in the cable connected at block A. Answer in Newton.Block B has a weight of 9 kg.AB

The 5 kg block A travels to the right at va = 0.61 m/sec at the instant shown in the figure. If the coefficient of kinetic friction is f = 0.2 between the surface and A, determine the following: the velocity of block A when it has moved 1.2 m. Answer in m/sec. b. Acceleration of block A and B. Answer in m/sec2. а. с. Magnitude of the force in the cable connected at block A. Answer in Newton. Block B has a weight of 9 kg. B

The 5 kg block A travels to the right at va = 0.61 m/sec at the instant shown in the figure. If the coefficient of kinetic friction is f = 0.2 between the surface and A, determine the following: the velocity of block A when it has moved 1.2 m. Answer in m/sec. b. Acceleration of block A and B. Answer in m/sec2. а. с. Magnitude of the force in the cable connected at block A. Answer in Newton. Block B has a weight of 9 kg. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Plss help ASAP A)resulting acceleration in (m/s^2) B)estimate resulting pressure at the bottom of the tank in kilopascal
In the figure provided below: determine the vertical reaction at Point B and E.
Unit 4 Rotation Gravity, Satellites... An Fw-10200 N vehicle is stalled one-third of the way across a bridge Compute the support force Fsup that needs to be supplied at the support of the bridge farthest from the vehicle.
5.5
11.7 (A/B). A solid shaft carrying a flywheel of mass 100 kg and radius of gyration 0.4m rotates at a uniform speed of 75 rev/min. During service, a bearing 3 m from the flywheel suddenly seizes producing a fixation of the shaft at this point. Neglecting the inertia of the shaft itself determine the necessary shaft diameter if the instantaneous shear stress produced in the shaft does not exceed 180 MN/m². For the shaft material G= 80 GN/m². Assume all kinetic energy of the shaft is taken up as strain energy without any losses. [22.7 mm.]
Determine and explain thoroughly, a. the equations of the shear and bending moment curves for the beam and loading shown in the diagram. b. draw the shear and bending moment curves for the beam and loading shown c. the maximum absolute value of the shear and bending moment.(Show the solution). 24 kN 29 kN/m В A D 300 -3 m 2 m 1 m
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
draw the v and m diagram of the continuous beam shown below. determine the value of EI y
Reaction at support?
Determine the magnitude and location of Resultant of the loading shown relative to the free end. 20 N/m EDN/m VON/m రెలి N
The 2.5-Mg car is being towed by a winch. If the winch exerts a force of T = 132.2(s + 1) N on the cable, where s is the displacement of the car in meters, determine the speed of the car in m/s when s = 11 m, starting from rest. Neglect rolling resistance of the car.