the 4. The FMF induced in the armature of a 500-kw, 250-volt shunt generator, is 265.4 volts when the terminal voltage and Load cuppent are at rated values and the field current is 14.0 Amp. The at mature resistance including brushes and commutating-pole field is 0.0066 ohm. + If мееее Reqit: 2 RC AFA DC SOUR 250v (a) Terminal voltage (V) (5) Power Generated (Pg), watts Power output (Po), watts Electrical Efficiency of generator

the 4. The FMF induced in the armature of a 500-kw, 250-volt shunt generator, is 265.4 volts when the terminal voltage and Load cuppent are at rated values and the field current is 14.0 Amp. The at mature resistance including brushes and commutating-pole field is 0.0066 ohm. + If мееее Reqit: 2 RC AFA DC SOUR 250v (a) Terminal voltage (V) (5) Power Generated (Pg), watts Power output (Po), watts Electrical Efficiency of generator

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A short shunt compound generator supplies 100A at 110V. Armature resistance is 0.050 and the shunt field resistance is 570 and the series field of resistance is 0.042. if the SPL is 852, determine a)Eg b)Copper lossesin b.1)armature b.2)series b.3)shunt c)n
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
Full solutions for the question with explanation
Two shunt generators A and B operates in parallel and their load characteristicsmay be taken us straight lines. The voltage of the generator A falls from 240 V atno-load to 220 V at 200 A while that of B falls from 245 V at no load to 220 V at150 A. Determine the current which each machine supplies to a common load of300 A and the bus-bar voltage at this load.
1. Write down some advantages and disadvantages of different connections of three-phase transformers . (Write mainly for delta-delta, wye-wye, wye-delta and delta-wye)2. What is skew effect? Why is it important for the rotor of an induction motor?
5. Two shunt generators A and B operate in parallel and their load characteristics may be taken as straight lines. The voltage of A falls from 240 V at no-load to 220 V at 200 A, while that of B falls from 245 V at no-load to 220 V at 150 A. Determine the current which each machine supplies to a common load of 300 A and the bus-bar voltage at this load.
A short shunt compound generator delivers 150A at a terminal voltage is 230V. The shunt field current is 2.5A. The resistances of the armature, series field and diverter are 0.032-ohm, 0.015 ohm and 0.03 ohm, respectively. Calculate the electrical efficiency of the generator at this load.
A DC series generator is supplying a current of 5A to a series lighting system through a feeder ofto total resistance, 1.0 ohm. The terminal voltage is 2500 V. The armature and series fieldresistances are respectively 18 and 15 ohms respectively. A 30-ohm diverter resistance isshunted across the series field. Determine the power developed in the armature of thegenerator?
A three phase 6000 V alternator has the following O.C.C. at normal speed: Field current : 14 18 23 30 43 Terminal voltage: 4000 5000 6000 7000 8000 With armature short circuit and fall load current flowing the field current is 17 A And when the machine is suppling fall-load of 2000KVA at zero-power factor the field current is 42.5 A, and the terminal voltage is 6000 V. Determine the field current that required when the machine is supplying the fall-load current at 0.7 p.f. lagging.
A three-phase, 4-pole, 1,500 rpm alternating having a double layer-windings with 18 turns per coil. The slots per pole per phase are 10 and the coil span is 22 slots. The spread phase is 60 degrees and the flux per pole is 0.0625 Weber. If the armature windings are wye connected. a) Determine the generated voltage per phase and the line to line voltages. b) If the alternator is delivering a three - phase load of 1,200KW at 0.8 lagging power factor what is the line current of the alternator
Discussion:- 1. What do you understand by "armature- reaction"? Discuss the effect of armature reaction in an alternator when it is loaded with resistive, inductive and capacitive loads. 2. Give the value of voltage regulation for different power factors at full load current and interpret their values.
4. A 2 MVA, 2.3kV, three-phase Wye connected alternator operates at rated kVA at a power factor of 80 %. The dc armature winding resistance between terminals is 0.08-ohm. The field takes 70-A at 125-V from the exciter equipment. Friction and windage loss is 20-kW, iron loss 36-kW and stray power loss are 2.0-kW. Calculate the efficiency of the alternator. Assume the effective armature winding resistance is 120% of the dc resistance.