The 20-mm diameter steel rod BC is attached to the lever AB and to the fixed support C. The uniform steel lever is 10mm thick and 30mm deep. Using the method of work and energy, determine the deflection of point A when L = 600 mm. Use E = 200 GPa and G = 77.2 GPa

Q: Q.I: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A:

Q: 2Mo Мо Find the amount of depression in mm at the midpoint of the bar AB. Mo= 1kNm, L = 1m, E = 200…

A: GIVEN :-  M0 = 1kNm = 1000 Nm                L = 1m               E = 200GPa = 200×109 N/m2…

Q: Question 3: The 60 mm diameter solid shaft is subjected to the distributed and concentrated…

A: unit of CC is N-m not KN-m . Because in solution unit of CC used is N-m.

Q: The uniform steel (E =200 GPa) bar in Fig. has a diameter of 40 mm and is subjected to the loading…

A: According to the given data  E=200GPa d=40mm L=AB=BC=CD=200mm We need to find Displacement of…

Q: 4. The cable will fail when subjected to a tension of 8000 N. Determine the largest vertical load P…

A:

Q: The set shown in the figure consists of an aluminum ABC tube, with section AB having a diameter of…

A: Givendiameter of tube AB d1=20mmdaimeter of section BC d2=60mmP=4000N

Q: The rigid beam supports the load of 50 kN as in the figure below. Determine the displacement at B.…

A: As per given question The rigid beam supports the load of 50 kN as in the figure below. Determine…

Q: Q4 An aluminium tube, 1.2 m long, has the semi-circular crossection shown in the fig. If the stress…

A: LA=Length of an Aluminum tube=1.2 mσS=Maximum shear stress=35 MPa=35×106 PaG=26 GPa=26×109…

Q: Show that for a plane curve the torsion T = 0.

A: To prove, T→=dr→ds=dx/dsdy/dso

Q: Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A:

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: steel rod is acted upon by the loading shown below. 50 mm2 is the area of the circular rod. The…

A: Given data: The area of the circular rod is A=50 mm2 The modulus of elasticity is E=200 GPa=200×109…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A:

Q: F2. A circular shaft fabricated from steel is supported at each end by rigid constraints, as shown…

A: Given data: LA=LB=60 in=5 ftT=900 ft.lbdA=2.5 in=0.208 ftdB=2 in=0.1667 ft Need to determine the…

Q: The 45-mm solid shaft has an allowable shear stress of  τallow= 65 MPa. The torsional loadings…

A:

Q: determine the applied force F.

A:

Q: 100 N K 250 N 200 N 50 N No 500 mm 400 mm 1700 mm

A: Given; E=200 GPa=200000 MPaA =25 mm2

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

A:

Q: The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are…

A:

Q: Determine the nodal displacements at node 1, node 2, and node 3 as shown in the figure. One end of…

A: Since only single force acting on the bar, so every point on the bar is having same force only.…

Q: Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of…

A:

Q: Example 4: The 2014-T6 aluminum strut is fixed between the two walls at A and B. If it has a 2 in by…

A: Let us draw the free body diagram of the shaft,  From the table, we can find the relation of the…

Q: The steel member shown below has a diameter of 69 mm, modulus of elasticity of E = 200 GPa, and is…

A: Draw FBD

Q: The figure illustrates a torsion-bar spring OA having a diameter d = 12 mm. The actuating cantilever…

A:

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A:

Q: Assume portion ABC of the rod is made of steel (Ee= 200 GPa , v=0.3) and portion CD is made of…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.