This is a practice hw question not graded!! Analytical Model TutorialThe 20-g centrifuge at NASA's Ames Research Center in Mountain View, California, is a horizontal, cylindricaltube of length 58.0 ft. Another 20-g centrifuge of length L = 59.0 ft is represented in the figure below.Assume an astronaut in training sits in a seat at one end, facing the axis of rotation 29.5 ft away. Determinethe rotation rate, in revolutions per second, required to give the astronaut a centripetal acceleration of 20.0g.L/2KKKRIPart 1 of 4 - Conceptualize:Look carefully at the figure and imagine you are the astronaut sitting in the seat at the far right. As thecentrifuge rotates, you are experiencing an acceleration toward the center of the device. The faster thecentrifuge spins, the larger is that acceleration.The problem is asking for a rotation rate, measured in revolutions per second. Because the period of circularmotion is the number of seconds per revolution, we see that the rotation rate will be the inverse of the period.rotation rate =Continue

The 20-g centrifuge at NASA's Ames Research Center in Mountain View, California, is a horizontal, cylindrical tube of length 58.0 ft. Another 20-g centrifuge of length L = 59.0 ft is represented in the figure below. Assume an astronaut in training sits in a seat at one end, facing the axis of rotation 29.5 ft away. Determine the rotation rate, in revolutions per second, required to give the astronaut a centripetal acceleration of 20.0g.

The 20-g centrifuge at NASA's Ames Research Center in Mountain View, California, is a horizontal, cylindrical tube of length 58.0 ft. Another 20-g centrifuge of length L = 59.0 ft is represented in the figure below. Assume an astronaut in training sits in a seat at one end, facing the axis of rotation 29.5 ft away. Determine the rotation rate, in revolutions per second, required to give the astronaut a centripetal acceleration of 20.0g.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Subject :Renewable energy System List tools which can be used to for minutes ahead forecasting?
Identify the function of the following types of valves (control or isolation or safety) a) Butterfly valve b) Globe Valve c) Check Valve / NRV / One-Way valve d) Knife gate valve e) Needle valve
Which fixture would be the most suitable for welding up and drilling the holes for fixture for the complete burglar bar within 100% accuracy
QUESTION 31 A multi-cylinder engine is to run at a constant load with an average speed of 600 rpm. The magnitude of the areas above and below the mean torque line are as follows: +2096, -2253.2, +2200.8, -2502.1, +2580.7, -2122.2 The speed fluctuation is 2% and moment of inertia of the machine is 60 kg.m² a) Calculate the necessary moment of inertia of the flywheel. b) The maximum and minimum speed throughout a cycle a) Determine suitable dimensions for cast iron flywheel. The density of cast iron is 7250 kg/m³, and its mass is 143.5 kg.
Can you explain what are in this table? and also explain an ideal condition in designing a friction clutch
Need questions 13, 14, 15 explained and answered please.
Discuss the line maintenance, repairs and alterations.
b) Write the differences between the boiler mountings and accessories.
Give four design features of flue gas analysis stack??
a.) A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated mean effective pressure (lb/in^2) if the length of the stroke is 0.5 foot, and the area of the piston head is 28.27in^2. The engine runs at 2700rpm with 12 cylinders. b.) What would be the Friction Horsepower of the Engine in (a.) if its BMEP is 150 lb/in^2.
:Q1: Answer the following by choosing the multiple choices (Vibration) ?What are the type of vibration in circular wood saws and fluid pipe, and why
Answer any one of the fallowing in details please