The 2.0-kg slider is released from rest in position A and slides without friction along the vertical-plane guide shown. Determine (a) the speed vg of the slider as it passes position B and (b) the maximum deflection o o the spring. 2.0 kg. 3.8 m k = 40 kN/m E 30 1.3 m 30

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Find in inches the inside diameter of this water pipe for an automatic icemaker. Express the answer…

A: Given     Outside diameter, d = 1 1/4 in                                  = 1.25 in…

Q: Says.003 is wrong

A:

Q: Metalworking According to standard American wire size tables, 3/0 wire is 0.4096 inches in…

A: Given: 3/0 wire is 0.4096 inches in diameter To  find: Write this size to the nearest 32nd of an…

Q: corresponding Circle the letter to the view on the right that shows the result of rotating the…

A: Find Rotate the object about the given axis.

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: Solve for T 2 in the figure.

A: Using the concept of equilibrium, the summation of all forces in the horizontal direction can be…

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given    Wind power generated, P = 1.3 MW                 Power coefficient = 025

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: Compute the thickness of the web, t, of the channel shape section

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E = 200…

A: The distributed load is The load is The modulus of elasticity is The moment of inertia is

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.