The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjectedto an external load of 15 kN as shown. Calculate the maximum circumferential and longitudinal stresses(in MPa) experienced by the tank. The thickness of the tank is 30 mm.175 cm60cm115 KNØ'15 KN

Givenh=2mP=2MPaFex=15kNt=30mm=0.030m

Answered: The 2-meter-high pressure tank below…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve for the pressure differential in Pa if the temperature inside a 3.46m vertical wall is 23.52°C, and at the outside is -16.27°C. Assume equal pressures at the top. Express your answer in 3 decimal places.
An 8 mm thick steel plate has an outside diameter of 600 mm and a length of 3 m. The plate is subjected to and internal pressure of 2 MPa. 54. When the tank is filled with water, determine the circumferential stress in MPa Determine the longitudinal stress in MPa at the bottom of the tank when filled with water.
A thick walled cylinder has an inner radius, a, of 95 mm and an outer radius, b, equal to 1.4a. The cylinder is subjected to an internal pressure, P, of 8 N/mm². Determine the circumferential stress at the inner radius of the cylinder. Give your answer in N/mm².
2. Given the two compartment vessel as shown in the figure. Gage A reads 85 psig, gage B inside the compartment X reads 25 psig. If the barometer reads 30.61 in Hg, determine the reading of gage C. (20 pts) P= 85 psig P=25sig
Read the question carefully and give me right solution according to the question.
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
Calculate the value of the hydrostatic pressure force acting on the septal septum shown in the diagram, given that the diameter of the diaphragm D = 1.5 and its length I = 1 he Fx
A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously to internal and external pressures. If the internal pressure is 25 MN/m2 and the hoop stress at the inside of the cylinder is 45 MN/m2 (tensile), determine the intensity of the external pressure,
Determine the safe internal pressure of a cylindrical tank with a 500 mm internal diameter, 20 mm wall thickness and 3 meters length, if the stress is limited to 40 MPa. Select the correct response: 3.8 MPа 4.2 MPа 5.2 MPa 3.2 MPа
The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
Q4//Determine the required vertical force F to be applied at the lower edge to open the square gate (2.8m*2.8m) as shown in figure below: Negative pressures 8250Pa 1.8m Gasoline s-0.7 hinge gate
A water tank, 7 m diameter, is made from steel plates that are 12.5 mm thick. Find the maximum height to which the tank may be filled if the circumferential stressis limited to 42 N/mm?. The specific weight of water is 9.81 kN/m³.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjecte to an external load of 15 kN as shown. Calculate the maximum circumferential and longitudinal stresse (in MPa) experienced by the tank. The thickness of the tank is 30 mm. 175 cm 60cm 115 KN