The 1200-lb weight is suspended from a cable that runs over a small pulley attached to the boom ABC. The boom is supported by a ball-and-socket joint at C and two cables attached at B. Neglecting the weight of the boom, determine the yension in cable BE. Kindly show correct FBD

Q: Beam AD carries the two 40-lb loads shown. The beam is held by a fixed support at D and by the cable…

A: Draw the free body diagram of the beam and the weight saperately: From the free body diagram of the…

Q: Determine the horizontal and vertical reactions at pin A on member AB. Roller E is pinned to the…

A: Given: The weight of body, W = 1500 lb

Q: Q.3- If block B weighs 325N and block C weighs 175 N, determine the required weight of block D and…

A: We can see the FBD of the joint A

Q: E G 100 kN 3 m to 200 kN 3 m B 4 m

A: Force in member BC is 375 kN [Compression] and force in member CG is 125 kN [Tension].

Q: The ramp shown weighs 400lb and is hinged to the truck frame on each side. it is also held in the…

A:

Q: Question 6 Neglecting the weights of the bar and the pulley and assuming the weight of the ball B to…

A:

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C…

A: Given that force applied is 32 lb  Required: Normal force at C

Q: A rope passes over a frictionless pulley at D, as shown. The cylinder weighs 300 lb. Determine the…

A: The free body diagram of the beam is as follows: Calculate the moment about point A as follows:…

Q: Determine internal reaction at the point located between A and C, 0.7 m to the right of A. Disregard…

A:

Q: Determine the size of a galvanised iron pipe needed to transmit water a distance of 180 m at 0.085…

A: Frictional loss is that part of the total head loss that occurs as the fluid flows through straight…

Q: To test the deflection of the uniform 220-lb beam the 120-lb boy exerts a pull of 39 lb on the rope…

A:

Q: Member ABC is rigidly fixed to the collar at A. The collar can slide freely on the pole and can…

A:

Q: The hand brake for a bicycle is shown. Portions DE and FG are free to rotate on bolt A which is…

A: Introduction: Tension is the force that is exerted when two physical objects collide. The force…

Q: For the lightweight truss which is loaded as shown 10 kN 5 kN -6 m -6 m· A B 4 m D -6 m 3m 3m By…

A: given truss as shown below

Q: Solved Determine the reaction forces at the supports A and B

A:

Q: The vertical bar is cantilevered to the floor as shown. Determine the reactions at B.

A:

Q: For the frame shown, neglect the weight of the members and the frictionless pulleys, what is the…

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A:

Q: Find the forces in each member and specify if it is in tension or compression. At E is pin support…

A:

Q: Determine the tension developed in wire CD required for equilibrium of the 37 lb cylinder E and the…

A: Given  Weight, WE = 37 lb              WF = 46 lb Find   Tension in CD, TCD

Q: Q 3: Determine the maximum weight of the engine that can be supported without exceeding a tension of…

A:

Q: Q.4. Determine the weight of the engine that can be supported at point A if a tension of 5000 N in…

A: Tension in cable AB is 5000N

Q: DETERMINE THE REACTION AT A AND C.

A: Given data  Given force system

Q: The 2kg member is supported by the pin and bracket at A and a cable at B as shown. Cable EBD passes…

A:

Q: F A B,

A:

Q: m OAB is supported by a ball and socket at point O and two cables AC and AD. Determine ported by the…

A: The reaction force at 'O'  can be written  as followsR0=[Oxi+Oy j+Ozk] KNTension at ACThe force is…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.