The 100-mm-diameter commercial steel pipe discharges 0.025 m³/s of water at 25°C through the nozzle at B with a diameter of d-42 mm. (Eloure 1) Part A Determine the pressure at A. The minor head loss coefficient for the nozzle is K-0.15. Express your answer to three significant figures and include the appropriate units.

The 100-mm-diameter commercial steel pipe discharges 0.025 m³/s of water at 25°C through the nozzle at B with a diameter of d-42 mm. (Eloure 1) Part A Determine the pressure at A. The minor head loss coefficient for the nozzle is K-0.15. Express your answer to three significant figures and include the appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absoluteviscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26.4. Determine the head loss due to friction.
FLUID POWER TECHNOLOGY 5) Figure 2 below shows the hydraulic system pumping oil (SG = 0.8) from a reservoir to a piston. The system consists of 13.72-m long 38-mm diameter cast iron pipe throughout, two 90º flange long radius elbows, a fully open globe valve and a sharp exit into the piston. K value is tabulated inside Table 1. If p1 = 7 bars, determine total head loss of the system and gauge pressure p2 in order to deliver water at 2 liter/s. Take kinematic viscosity of oil, = 1 × 10-4 m2/s.
8. A horizontal pipe has a non-negligible expansion (K, =(1 Asmall Atarge/ ) as shown in the figure. The water flows through the pipe and the velocity (V1) and the pressure (P:) in the smaller-diameter pipe are 10 m/s and 300 kPa, respectively, and the flow is turbulent. Assume that the major loses are negligible, kinetic energy correction factor is 1.06 at both the inlet (a1) and the outlet (a2), and the density of water is 1000 kg/m?. a) Determine the outlet pressure P2 considering the losses and kinetic correction factor b) find the error that would have occurred if Bernoulli's equation had been used ignoring all the losses and the kinetic energy correction factor. 8 cm 16 cm Water
A 300mm x 300mm pipe discharges 600 L/s of water where the length is 300m. Determine the head loss if f = 0.021
What is the head loss at the outlet of the pipe that discharges water into the reservoir at a rate of 10 cfs if the diameterof the pipe is 12 in.?
Oil of SG=0.87 and a kinematic viscosity v = 2.2 x 10-4 m²/s flows through the vertical pipe shown in the figure below at a rate of 5 x 10-4 m³/s. Determine the manometer reading, h. Assume SGm = 1.3, D = 18 mm, / = 3 m. h = i SG m te SG SUPPORT
Given the 0.063 m length of the syringe. F=1N a. provide an equation to calculate its water flow rate if water is going to travel from a 0.063 m length of syringe with dextrose tube length of 0.5 meter to another 0.063 m syringe (see attached photo). The Inner diameter of the syringe is 0.02. While the inner diameter of dextrose tube is 0.003. b. provide an equation in order to calculate the maximum force or pressure that exerts in plunger in order to travel the water at its maximum speed.
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then is suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. Pipe coefficient f=0.005 and the contraction coefficient at sudden change in area is 0.58. Find all the losses, in terms of velocity v2 at exit from the 50 mm2pipe and hence find rate of flow. Draw the Hydraulic gradient line.
In the figure below, assume the pipe from B to C has a diameter of 4-inches, (f = 0.035), and length of 18-feet. The pipe from DE is 187-feet, has a diameter of 4-inches and friction factor of 0.035. The Az = 69-feet. The elevation of C is 14-feet above the lower water surface. If the pressure head @ C is to be no less than (-) 20 feet, and the pump has 63% efficiency, what horsepower must be supplied to the pump in order to convey flow through the system? (Kent = 0.8) Assume a submerged exit. Az
In a commercial steel pipe of diameter 0.01906 (in meters), industrial waste water (approximate as water at 30 °C) flows through it with an average velocity of 30 m/s. Determine the pressure drop using Moody chart. Determine the pressure drop using Colebrook Formula or Haaland Equation.
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
Water at 15°C is pumped from a reservior at a rate of 0.2428 m³/s where the local atmospheric pressure is 96.5 kPa. The total head loss in the suction pipe is 1.1 m. From the manufacturer data, the NPSH required at this operating point is 6.6. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places. (10 mins) hs Vs Suction pipe Free surface of liquid Sump