Task 5 Steam flows steadily through an adiabatic turbine. The inlet conditions of steam are 4 MPa 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Steam table is available. P = 4 MPa T- 500°C V = 80 m/s Determine: (a) the change in kinetic energy per unit mass A ke (kJ/kg) Steam (b) the change in enthalpy per unit mass A h (kJ/kg) ni= 12 kg/s W ut (c) the work done per unit mass (kJ/kg) (d) the power outnut (MW)

Task 5 Steam flows steadily through an adiabatic turbine. The inlet conditions of steam are 4 MPa 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Steam table is available. P = 4 MPa T- 500°C V = 80 m/s Determine: (a) the change in kinetic energy per unit mass A ke (kJ/kg) Steam (b) the change in enthalpy per unit mass A h (kJ/kg) ni= 12 kg/s W ut (c) the work done per unit mass (kJ/kg) (d) the power outnut (MW)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need an answer quickly please.
DRAW ONLY THE FBD OR FREE BODY DIAGRAM FOR THE GIVEN FIGURE. COMPLETE FBD WITH LABELS. WRITE LEGIBLY OR TYPEWRITTEN FOR UPVOTE. NO UPVOTE IF INCOMPLETE
Q2. A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected while the direction of the launching velocity at B and the orientation of the underneath ground are 30° and 40° from a horizontal axis x, respectively, determine: (a) the launching velocity of the skier at B using the formulation of conservation of energy. (b) the distance, s where the skier lands at C by considering motion in x and y axes.
Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.
Shaft G-Codes programming process (sumerik)
Refer to the figure below. Read the feature control frame in the figure and write it out below. 0.010MABMCM
Select all the correct statements: a. Moment of force or toque is force multiplied by the perpendicular distance from the point of application of the force to the selected point or center. b. The perpendicular distance is also termed as moment arm. C. The axis of the moments and the planes of the forces are intersecting at the center of the moment. d. Graphically, the moment can also be defined as the area of the triangle formed by joining the center of moments with the ends of the forces. B
b) You are given a set of six links. The lengths of the links are as follows: 6.3cm, 9.1cm,12.4cm,15.6cm,20cm,40.2cmSketch a crank-rocker mechanism you can realize using a selection of four links from the set.
DESCRIPTIVE GEOMETRY