Task 5 Considering multi-mechanical systems involved in heat engine as shown in figure 4 to determine: a) The net work done per cycle b) The engine's thermal efficiency c) Critically compare how changes in the thermal efficiency of a heat transfer process can affect the behavioural characteristics of mechanical systems (Assume the gas is monatomic). (D2) p (kPa) 300 K isotherm 200 - 100 - V (cm') 200 400 600 Figure 4. Heat engine

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: Sketch the isometric view Sketch the first angle orthographic view Note:use creo parametric to…

A:

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Vega is a star that is 25 lightyears away. A spaceship is to travel to Vega at a speed of 0.625c. a.…

A:

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 7-Either the following text: Standardization is an activity that consists of developing rules…

A: It is asked to generate stick scriptWhat is te role of orientation marker How the inscription…

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: how do i draw sectional view of this object.

A: A sectional view of an object is used to identify the parts interior construction of a part…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: How to draw 4/5 × 2/3 on a model

A: A mixed fraction is a fraction that has both a quotient and a remainder. 2 1/3, for…

Q: I need these 3 parts answered TRUE or FALSE.

A: During the life of any product, parts used for many years are replaced to improve the efficiency or…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.