Table Q2 shows op-amps that are available for A1. Calculate the FoM for each op-amp and choose an appropriate device. In your answer you must explain your decision. There should be a table and a graph (Cost versus FoM) to support your analysis. Table Q2 Op-amp OP07 OP277 OP97 OP1097 LT1050 Offset voltage (μV) (max) 150 50 75 50 5 Offset current (PA) (max) 6000 2800 150 250 125 Price per unit (RMB) 3.6 15.3 22 29.1 36.5

Table Q2 shows op-amps that are available for A1. Calculate the FoM for each op-amp and choose an appropriate device. In your answer you must explain your decision. There should be a table and a graph (Cost versus FoM) to support your analysis. Table Q2 Op-amp OP07 OP277 OP97 OP1097 LT1050 Offset voltage (μV) (max) 150 50 75 50 5 Offset current (PA) (max) 6000 2800 150 250 125 Price per unit (RMB) 3.6 15.3 22 29.1 36.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

11)This Multiple choice questions from electronics lab course &just write for me final answer ,It easy for you.
answer those questions (True and False).. Please answer all subpart I will like it please only true or false.. please all..
Q1 Analyse the circuit shown in Figure Q1, (a) Name the function of each Op-Amp, A1, A2, A3, and A4 (b) (i) Determine the output for each Op-Amp (Vo1, Vo2, Vo3 and Vo4). (ii) Draw all the waveforms based on the answer in part Q1(b)(1). R1 R2 O Vo1 10k2 56kN |+15V R3 R4 A1 -O Vo2 Vi + 0.3 sin ot V 10k2 68kN |-15V C |+15V +15V Vo3 RS 1 Hz A2 33µF АЗ |+15V Vo4 -15V 100k2 A4 -15V 1-15v I-15V Figure Q1 + +
Q3. This question is on op-amps. (a) Comment on the differences between the values in the two columns of properties in the table for both an ideal op-amp and a typical 741 op-amp. Fill in the two missing values. Op-amp Gain Input resistance Unity Bandwidth Short circuit current Output resistance Ideal Infinite Infinite Infinite 0 741 200000 1MHz 25mA 75 ohms
electronic circuit analys design
Voltage when applied at 2 inputs of Op-amp to get 0 V of output is called_voltage. O a. Output offset O b. Input offset O. All of these O d. In-out offset
Vin -100m/100mV. 10kHz RI B10k RF 100k Vcc +12V U1 UA741 A RL 25k -12V Vee 1. What are the basic features of an OP-AMP? (6) 2. Basic op-amp connections include what? (10) 3. Simulate the circuit using Circuit maker and explain the different between A and B.
2)For the following circuit, assuming the Op-Amp is ideal, fill in the table for the missing values when vi = 2V, 12 10 k [mA] [mA] [mA] [mA] ...... I kn lo I2 ...... IL Io o vo vi ........
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
4. Determine the voltage gain of the non-inverting op-amp with Rf-100k and R1=4.7k02. Calculate the output voltage if the input voltage is 200mV
The operational amplifier (op-amp) in Figure 1 is an ideal op-amp with maximum output voltage, vO(max) is +12 V and the minimum output voltage, vO(min) is -12 V. A sine wave with ±5V peak-to-peak voltage is applied as the input, vin as shown. For each of the following conditions, derive or explain the relationship between output voltage, vo and input voltage, vin, and then draw the input and output voltage waveforms on same graph. Label the x-axis, y-axis, peak voltages and units. 1.R1 = R2 = R3 = 10 kΩ and RF = 3R1. 2.R2 = R3 = 10 kΩ, RF = 3R2 and R1 is broken (open circuit). 3.R1 = R2 = R3 = 10 kΩ and RF is broken (open circuit). 4.R1 = R2 = 10 kΩ, RF = 3R1, R3 is broken (open circuit) and the op-amp’sinverting and non-inverting terminals are accidently interchanged where node ‘x’ is connected to the non-inverting input while node ‘y’ is connected to the inverting input of the op-amp.
draw the block diagram of op-Amp