Table below presents the capillarypressure curve of anundersaturated oil reservoir. The oilwater contact is located at a depthof 4352 ft. the oil density atreservoir conditions is po= 39.5Ibm/ft3, and the water density ispw=64 Ibm/ft3. Using the capillarypressure information in the table.Plot depth versus water saturationWater saturationCapillary pressure (psi)0.169.000.24.200.32.000.41.150.50.800.60.620.70.550.80.480.90.4610.45

Write the formula for the height of oil above the free water level i.e. the height above the…

Table below presents the capillary pressure curve of an undersaturated oil reservoir. The oil water contact is located at a depth of 4352 ft. the oil density at reservoir conditions is po= 39.5 Ibm/ft3, and the water density is pw=64 lbm/ft3. Using the capillary pressure information in the table. Plot depth versus water saturation Water saturation Capillary pressure (psi) 0.16 9.00 0.2 4.20 0.3 2.00 0.4 1.15 0.5 0.80 0.6 0.62 0.7 0.55 0.8 0.48 0.9 0.46 1 0.45

Table below presents the capillary pressure curve of an undersaturated oil reservoir. The oil water contact is located at a depth of 4352 ft. the oil density at reservoir conditions is po= 39.5 Ibm/ft3, and the water density is pw=64 lbm/ft3. Using the capillary pressure information in the table. Plot depth versus water saturation Water saturation Capillary pressure (psi) 0.16 9.00 0.2 4.20 0.3 2.00 0.4 1.15 0.5 0.80 0.6 0.62 0.7 0.55 0.8 0.48 0.9 0.46 1 0.45

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing through is measured with a U-tube manometer (Rm,1) as 10 cm (1st situation). The manometer fluid is carbon tetrachloride (CC14). Then, in order to avoid CC14 poisoning, it is decided to add a layer of water to both arms of manometer (2nd situation). So, 4 cm of water is added to the left arm and 8 cm of water is added to right arm. In this new situation, what will be the height difference of manometer fluid (CC14) between the arms of the manometer (Rm,2)? Data: pbenzene=876 kg/m³, pwater=997 kg/m², pccCI4=1587 kg/m³ Benzene Flow Benzene Flow "wright=8cm Rm,1 Rm2 =4cm[ 1 st Situation: Before adding water to manometer's arms 2 nd Situation: After adding water to manometer's arms
Need Solution through 15min
In mechanical fluid
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. FIND: A. The hydrostatic force due to linseed oil F1. B. The hydrostatic force due to castor oil F2. C. The hydrostatic force due to water. D. The net hydrostatic force acting on the gate Fnet
Figure 0 shows the change in density of a newtonian fluid with temperature, ing/m^3.Falling spere experiments give average times of 0.2s @ 10 c and 0.23s @ 20 cUsing the equation u=K(ps-pf)tWhere K is found to be 1.34Ps=2300 kg/m3Calculate the viscosity of the fluid at 20 c and 10 c
Solve correctly please, with detailed explanation required.
If a closed tank contains compressed air and oil (SGoil = 0.90), with a U-tube manometer using mercury (SGHg = 13.6), is connected to the tank as shown in the figure below. For column heights h1=1 m, h2= 25 cm, and h3= 245mm then the pressure exerted on the system by the mercury is kPa Air Cil Pressure gage (1) Open (2) H₂
Pipeline A has oil of relative density 0.85 and pressure gauge reading at B is 330 kPa.
Please explain this MCQ Asap
For the manometer shown in the image, all fluids are at 20°C. If PB- PA = 90 kPa, determine the height H in centimeters. The specific weight of water is 9790 N/m³ and the specific weight of mercury is 133100 N/m³. Meriam red oil, SG = 0.827 Water 18 cm H 35 cm Numeric Response B Mercury
Fast plz
A well is 3500 meters deep and 3100 meters vertically deep. It is filled with two drilling fluids, the first with a density of 10.5 lb/gal located up to 1000 meters and the rest of the well is filled to the bottom with fluid with a density of 12 lb/gal. During the operation, a wellhead pressure equivalent to 320 psi was recorded. With these data in hand, the pressures occurred at the bottom of the well and the equivalent density of the bottom of the well in lb/gal are, respectively: The. 6389 psi/12.12 lbs/gal 6429 psi/ 12.1 lbs/gal 5959 psl/13.2 lbs/gal 6220 psi/11.9 lbs/gal E 20:13 + 130% =