Data from the compression test on sample (i) is shown in Table 2. Plot thestress versus strain curve for this sample? Table B2: Stress-strain data for uniaxial compression test on SampleNormal stress Uniaxial strain (%) Lateral strain (%)(MPa)0.00.00000.00005.00.0319-0.015010.00.0720-0.027515.00.1025-0.042520.00.1450-0.060025.00.1755-0.072530.00.2150-0.087535.00.2455-0.102541.00.2815-0.112546.00.3125-0.120952.00.3515-0.128558.00.4000-0.1325

The stress strain curve of the sample is as follows

Table B2: Stress-strain Normal stress (MPa) 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 41.0 46.0 52.0 58.0 data for uniaxial compression test on Sample Uniaxial strain (%) Lateral strain (%) 0.0000 0.0000 0.0319 -0.0150 0.0720 -0.0275 0.1025 -0.0425 0.1450 -0.0600 0.1755 -0.0725 0.2150 -0.0875 0.2455 -0.1025 0.2815 -0.1125 0.3125 -0.1209 0.3515 -0.1285 0.4000 -0.1325

Table B2: Stress-strain Normal stress (MPa) 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 41.0 46.0 52.0 58.0 data for uniaxial compression test on Sample Uniaxial strain (%) Lateral strain (%) 0.0000 0.0000 0.0319 -0.0150 0.0720 -0.0275 0.1025 -0.0425 0.1450 -0.0600 0.1755 -0.0725 0.2150 -0.0875 0.2455 -0.1025 0.2815 -0.1125 0.3125 -0.1209 0.3515 -0.1285 0.4000 -0.1325

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the transverse rupture strength for the flexure test for a brittle material having the following data: b=50mm, t=20mm, L=160 mm and the applied load 300 kg.
Discussion: Compression Test In compression test a greater load is necessary to cause yielding than that required in tension test for the same sample. State the reason • Advantages of Stress_ Strain curve. Sources of errors in the experiment. • Reasons for the barrel shape of the tested specimen and how could we minimize this defect. The conditions required to achieve a reliable compression test.
During the triaxial test measurements, local strain gauges were attached to the specimens for high quality measurements to be performed. It was revealed that for the sandstone collected from a depth of 80 m and tested at 0.6 MPa of isotropic confining pressure, at a volumetric strain of 3.0x10-1%, the material was still in the linear-elastic range of behavior. If for the given conditions, the specimen has a true Young’s modulus of 0.286 GPa, a Poisson’s ratio of 0.28 and is assumed to be an isotropic material, determine the deviatoric stress which corresponds to the said volumetric strain of 3.0x10-1%.
An intact solid cylindrical specimen of diameter 50 mm and thickness 30 mm is prepared from a Hoek-Brown rock material with m,= 10. If the disc fails under a diametral compressive force of 7.8 kN as shown opposite, determine the brittleness index of the tested material based on stresses induced at the centre of the loaded specimen; i.e., the ratio of the material's compressive to tensile strength. Assume that the Hoek-Brown failure criterion is valid for the plane stress field condition developed at the centre of the specimen. 7.8 kN P B
20 - During stress strain test on rock sample ,if the axial and lateral strains are 0.048 and 0.012 respectively , The Poisson ratio is; a) 0.25 b) 4.0 0.025 0406933 d) 0.4
In a CBR test, the load sustained by a remoulded soil specimen at 5 mm penetration is 120 kg. The CBR value of the soil will be:
In a direct shear test of a 2-inch by 2-inch (SP) specimen, the vertical weight was 31 Ib, and the horizontal load at failure was 19 Ib, the weight of the sample 70 grams and the sample thick 0.7 inch, the estimate effective friction angle for this test is
Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
Soil
The followings are data from the unconfined compression test. Use these data to determine the unconfined compression strength of the soll and the undrained cohesion. Diameter of sample = 1.6 cm; Length of sample= 4.0 cm; Dial gauge factor = 0.02 mm Reading 0 20 Load (kN) 40 60 80 0.000 0.004 0.007 0.009 0.011 100 0.012 120 140 160 0.013 0.014 0.015 180 200 220 240 260 0.016 0.016 0.016 0.016 280 0.016 0.016
K1
Please answer question 7